EXHAUST MANIFOLD GASKET, 13B 93-95 (USES 2)
Exhaust Manifold Gasket, 13B 93-95 (Uses 2)
Sold individually
| SKU: | 13-4610-N3A1 |
| Manufacturer SKU: | N3A1-13-461 |
EXHAUST MANIFOLD GASKET, 13B 93-95 (USES 2)
The engine uses two and these are sold individually. Order two for a complete job.
$185.29
Related Products:
-
EXHAUST HANGER, 93-95 @ MUFFLER 2 REQUIRED
Exhaust Hanger at Muffler, 93-95 2 Required
Go To Our FAQ for Exhaust Hangers to see the locations and part numbers of the hangers for your car.
SKU: 40-061F-N3A1 Manufacturer SKU: N3A1-40-061F -
EXHAUST HANGER, 93-95 @ CONVERTER
Exhaust Hanger at Converter, 93-95
Go To Our FAQ for Exhaust Hangers to see the locations and part numbers of the hangers for your car.
SKU: 40-061A-N3A2 Manufacturer SKU: N3A2-40-061A -
EXHAUST HANGER 93-95, @ MID MUFFLER PIPE
Exhaust Hanger at Mid Muffler Pipe 93-95
SKU: 40-0610-FE20 Manufacturer SKU: FE20-40-061 -
EXHAUST CONVERTER GASKET 93-95 MAIN FRONT & REAR
Exhaust Converter Gasket 93-95 Front and Rear of Main
SKU: 40-3050-RF36 Manufacturer SKU: RF36-40-305 -
SPLIT AIR PIPE TO MANIFOLD GASKET 86-95 TURBO
86-95 Turbo Split Air Pipe To Manifold Gasket
SKU: 13-164A-N318 Manufacturer SKU: N318-13-164A -
SPLIT AIR EXHAUST GASKET, 81-95 PIPE TO CAT
Split Air Exhaust Gasket, 81-95 Split Air Pipe To Cat
SKU: 40-3750-YJZ4 Manufacturer SKU: YJZ4-40-375
You May Also Like:
-
EXHAUST SYSTEM DUAL, 12A DUAL PIPE 79-85
Racing Beat Dual Exhaust System, 12A Dual Pipe 79-85
SKU: 16422 -
-
EXHAUST STUD, RENESIS EXHAUST MANIFOLD TO ENGINE
Exhaust Stud Renesis, Exhaust Manifold to Engine (4 Required)
SKU: 13-708A-SL50 Manufacturer SKU: SL50-13-708A -
-
-
EXHAUST PRE-SILENCER WITH DOWN PIPE, 88 CONVERTIBLE MANUAL
Racing Beat Exhaust Pre-Silencer with Down Pipe, 88 Convertible Manual Transmission Non-Turbo
Down Pipe with Presilencer – 1988 RX-7 Convertible Non-Turbo (w/Manual Transmission) – The 1986-92 13B 6-port engines, in stock form with the factory fuel injection, produces similar power gains with either our Header/Presilencer combo or our RX-7 Down Pipe/Presilencer combination. If you have no intentions of installing RB’s Holley intake System (or any other aftermarket carb set-up), we recommend the use of the down pipe/Presilencer combo since it offers a slightly quieter exhaust note, is easier to install and less costly. If you are intending to upgrade the intake or fuel injection system, the Header/Presilencer combo offers the greatest performance potential.
The 1988 RX-7 Convertible (w/ Manual Transmission) Down Pipe/Presilencer combination incorporates a 2.5-inch O.D. Down Pipe and our perforated stainless steel core and stainless steel wool-packed Presilencer to boost power approximately 13% – an 18 horsepower increase on a 1987 RX 7- and maintain a comfortable exhaust noise level during full power driving.
The replacement pipe connects to the factory exhaust manifold, and the presilencer connects to the factory Y-pipe, replacing all catalytic converters and intermediate tubing. (The downpipe cannot be used as a “bolt-up” component to replace just the catalytic converters.)
The Racing Beat presilencer is equipped with an exhaust back-pressure tube for correct operation of the 6-port actuators. Installation of this requires the removal of the air control and check valve and the air pump. This kit includes all necessary mounting hardware, air control & check valve cover plate, and gaskets (1 Back Pressure Pick-up and 3 Replacement Pipe-to-Presilencer gaskets).
SKU: 16209