EXHAUST PRE-SILENCER, 87-92 TURBO
Racing Beat Exhaust Pre-Silencer, 87-92 Turbo
| SKU: | 16406 |
EXHAUST PRE-SILENCER, 87-92 TURBO
The Racing Beat Power Pulse Presilencer for the 1987-92 RX-7 TURBO II is designed to be used with our wide selection of RX-7 headers to complete a bolt-on configuration to the Y-pipe section.
This same Power Pulse Presilencer is included as a sub-component with the Downpipe/Presilencer Assembly we offer for the TURBO II. Furthermore, these Power Pulse Presilencers are ideal for those individuals wanting to fabricate custom exhaust systems incorporating either long or short primaries.
The Racing Beat Power Pulse Presilencer improves the character of the exhaust noise, dramatically reducing the inherent, obnoxious metallic high frequency noise with virtually no power loss. Constructed using a stainless-steel shell, interior core tube, and high temperature stainless packing wool, the Power Pulse Presilencer measures 20-inches in length with a 4-inch outside diameter. Each end is fitted with 12mm studs. The hanger provided will allow correct fitment onto the application listed.
The TURBO II Power Pulse Presilencers are manufactured with a large diameter 2.5-inch I.D. core pipe for improved exhaust gas flow.
$291.06
Related Products:
-
Exhaust Down Pipe for 87-92 TURBO 2 1/2″
This Down Pipe is available for custom applications in a 1987-91 RX-7 Turbo II application.
This 2.5-inch down pipe fits either manual or automatic transmission equipped cars and eliminates the catalytic converter sections.
This down pipe bolts to the stock turbo, but the use of our presilencer (or a suitable replacement) is required to connect this assembly to the Y-pipe section. If you need to retain a catalytic converter in your exhaust system, you may find a suitable unit offered in the aftermarket. Although the replacement of your stock catalytic converters with a single aftermarket unit is technically NOT legal, this approach may suit your emissions needs. We suggest you contact your local emissions testing facility for more information. Gaskets sold separately.
.
SKU: S16207 -
EXHAUST HANGER, 86-92 BAND+ SLEEVE
Exhaust Hanger with Steel Band around it and a sleeve, 86-92
Go To Our FAQ for Exhaust Hangers to see the locations and part numbers of the hangers for your car.
SKU: 40-060B-N328 Manufacturer SKU: N328-40-060B -
MUFFLER UNIVERSAL, STAINLESS 2.5″ RACING BEAT
Racing Beat Universal Stainless Muffler 2.5″ ID
SKU: 16025 -
-
EXHAUST PRE-SILENCER WITH DOWN PIPE, 86-92 TURBO
Racing Beat Exhaust Pre-Silencer wih Down Pipe, 86-92 Turbo Coupe
SKU: 16207 -
EXHAUST SYSTEM, 86-92 TURBO
Racing Beat Exhaust System, 86-92 Turbo
1987-91 RX-7 TURBO REV II Complete High Performance Exhaust System – If you own a TURBO II RX-7 and you’ve found your way to this webpage, congratulations! Why? Because your search for an exhaust system for your car ends here. Simply put, this is the ultimate exhaust for any Turbo II RX-7!
The REV TII High Performance RX-7 Exhaust is legendary with FC3S owners. This RX-7 exhaust system includes a 3-inch OD REV TII Down Pipe from the turbo outlet that mates to a REV TII Presilencer section. The outlet of the presilencer connects to the inlet of the REV TII Y-Pipe which routes the exhaust gases down two 2.375-inch OD (60mm) pipes into a pair of left and right REV TII Power Pulse Mufflers. Once installed, this bolt-on exhaust system increases horsepower approximately 32% – that’s a 59 HP increase on a 1987 Turbo II RX-7!
The REV TII High Performance RX-7 Exhaust system reduces exhaust gas back-pressure significantly, thereby allowing the un-assisted turbo boost pressure to increase to 10-11 psi. (Note: A fuel cut controller device is required to prevent fuel cutoff to the rear rotor above the factory pre-set limit.)
This bolt-on system uses the stock mounting points for ease of installation. Each system is supplied with all necessary mounting hardware and gaskets. (The kit does not include turbo outlet gasket, if needed it can be ordered separately.) The down pipe section is provided with a position for the oxygen sensor.
SKU: 16425
You May Also Like:
-
-
EXHAUST CONVERTER GASKET 93-95 MAIN FRONT & REAR
Exhaust Converter Gasket 93-95 Front and Rear of Main
SKU: 40-3050-RF36 Manufacturer SKU: RF36-40-305 -
-
-
EXHAUST SYSTEM DUAL, 13B DUAL PIPE 79-85
Racing Beat 13B 4 Port Dual Pipe Exhaust System 79-85
Will work on 6 Port if not using the actuators.SKU: 16423 -
MUFFLER UNIVERSAL, POWER PULSE 79-85 RACING BEAT
Racing Beat Universal Power Pulse Muffler, 79-85
In response to numerous requests from customers demanding a very low restriction“street capable” muffler, Racing Beat now offers the Universal Power Pulse PR-Extreme RX-7 Muffler with a 2.75″ OD internal perforated core design to meet the performance demands of high-horsepower ported rotary engines. The Power Pulse PR-Extreme RX-7 Muffler is compatible with all 1979-85 RX-7 muffler rear mounting positions and retains the factory stock appearance; this PR-Extreme RX-7 Muffler includes an inlet of 3″.
The Racing Beat Universal Power Pulse PR-Extreme RX-7 Muffler is manufactured by the same exhaust components manufacturer that has produced the “tried and proven” First Generation RX-7 Power Pulse mufflers (1979-80, 1981-82, and 1984-85) since the mid-1980s. Utilizing a heavy-walled canister shell and extremely durable heat and noise insulating materials, the Racing Beat Power Pulse PR-Extreme RX-7 Muffler is engineered for the high exhaust gas temperatures found in rotary engine applications.
The main body of the muffler canister measures 8 inches in diameter and 18 inches in length. The dual outlet tips are completely chrome-plated with straight-cut outlet.
Now may be the time to consider replacing the old rubber muffler hangers on your RX-7. New replacement hangers will ensure correct alignment of the RX-7 muffler canister and tip position in the bumper opening.
SKU: 16436