EXHAUST PRE-SILENCER, 81-83
Racing Beat Exhaust Pre-Silencer, 71-78, 81-83
The Racing Beat Power Pulse Presilencer for the 1971-78 & 81-83 RX-7 is designed to be used with our wide selection of RX-7 Streetable Headers to complete a bolt-on configuration. These Power Pulse Presilencers are ideal for those individuals wanting to fabricate custom exhaust systems incorporating either long or short primary exhaust systems.
The Power Pulse Presilencer improves the character of the exhaust noise, dramatically reducing the inherent, obnoxious metallic high frequency noise with virtually no power loss. Constructed with a high temperature, 2-inch I.D. perforated core of 304 stainless steel wrapped with high-temperature stainless steel wool, the Power Pulse Presilencer measures 20 inches in length with a 4-inch outside diameter. The mounting studs are 12mm both front and rear.
| SKU: | 16400 |
EXHAUST PRE-SILENCER, 81-83
$291.06
Related Products:
-
-
EXHAUST CENTER SECTION, 79-85 RACING BEAT 4 PORT/6 PORT
Racing Beat Exhaust Center Section, 79-85 4 Port/6 Port
SKU: 16398 -
EXHAUST HANGER, 2 SLEEVES
Exhaust Hanger, 2 Sleeves
Go To Our FAQ for Exhaust Hangers to see the locations and part numbers of the hangers for your car.
SKU: 40-1600-1114 Manufacturer SKU: 1114-40-160 -
-
EXHAUST CONVERTER GASKET, 81-85 MONO + 84-85(REAR)
81-85 Mono Converters Gasket, 84-85 Rear Main Converter Gasket
SKU: 13-621A-1480 Manufacturer SKU: 1480-13-621A -
EXHAUST CONVERTER GASKET, 81-85-FRONT 81-83-REAR
81-85 Front Main Converter Gasket
81-83 Rear Main Converter GasketSKU: 40-325A-1480 Manufacturer SKU: 1480-40-325A
You May Also Like:
-
EXHAUST HEADER 12A, 79-85 RX7 DUAL OUTLET
Racing Beat 12A Exhaust Header, 79-85 RX7 Dual Outlet
SKU: 16125 -
-
-
EXHAUST PRE-SILENCER WITH DOWN PIPE, 88 CONVERTIBLE MANUAL
Racing Beat Exhaust Pre-Silencer with Down Pipe, 88 Convertible Manual Transmission Non-Turbo
Down Pipe with Presilencer – 1988 RX-7 Convertible Non-Turbo (w/Manual Transmission) – The 1986-92 13B 6-port engines, in stock form with the factory fuel injection, produces similar power gains with either our Header/Presilencer combo or our RX-7 Down Pipe/Presilencer combination. If you have no intentions of installing RB’s Holley intake System (or any other aftermarket carb set-up), we recommend the use of the down pipe/Presilencer combo since it offers a slightly quieter exhaust note, is easier to install and less costly. If you are intending to upgrade the intake or fuel injection system, the Header/Presilencer combo offers the greatest performance potential.
The 1988 RX-7 Convertible (w/ Manual Transmission) Down Pipe/Presilencer combination incorporates a 2.5-inch O.D. Down Pipe and our perforated stainless steel core and stainless steel wool-packed Presilencer to boost power approximately 13% – an 18 horsepower increase on a 1987 RX 7- and maintain a comfortable exhaust noise level during full power driving.
The replacement pipe connects to the factory exhaust manifold, and the presilencer connects to the factory Y-pipe, replacing all catalytic converters and intermediate tubing. (The downpipe cannot be used as a “bolt-up” component to replace just the catalytic converters.)
The Racing Beat presilencer is equipped with an exhaust back-pressure tube for correct operation of the 6-port actuators. Installation of this requires the removal of the air control and check valve and the air pump. This kit includes all necessary mounting hardware, air control & check valve cover plate, and gaskets (1 Back Pressure Pick-up and 3 Replacement Pipe-to-Presilencer gaskets).
SKU: 16209 -
EXHAUST HEADER 13B, 89-92 6PORT DUAL PIPE
Racing Beat 13B Exhaust Header, 89-92 With 6 Port Actuation and O2 sensor fitting.
SKU: 16129 -
