EXHAUST PRE-SILENCER WITH DOWN PIPE, 89-92 NON TURBO AUTOMATIC TRANSMISSION
Racing Beat Exhaust Pre-Silencer with Down Pipe, 89-92 Non Turbo Automatic Transmission Coupe
Down Pipe with Presilencer – 1989-91 RX-7 Coupe Non-Turbo (equipped with Automatic Transmission) – The 1986-92 13B 6-port engines, in stock form with the factory fuel injection, produces similar power gains with either our Header/Presilencer combo or our RX-7 Down Pipe/Presilencer combination. If you have no intentions of installing RB’s Holley intake System (or any other aftermarket carb set-up), we recommend the use of the RX-7 Down Pipe/Presilencer combo since it offers a slightly quieter exhaust note, is easier to install and less costly. If you are intending to upgrade the intake or fuel injection system, the Header/Presilencer combo offers the greatest performance potential.
The Down Pipe/Presilencer combination incorporates a 2.5-inch O.D. Down Pipe and our perforated stainless steel core and stainless steel wool-packed Presilencer to boost power approximately 13% – an 18 horsepower increase on a 1987 RX 7- and maintain a comfortable exhaust noise level during full power driving.
The replacement pipe connects to the factory exhaust manifold, and the presilencer connects to the factory Y-pipe, replacing all catalytic converters and intermediate tubing. It is not possible to use just the down pipe to replace only the catalytic converters. The use of the presilencer is required to complete the connection to the y-pipe. Although a short length of tubing can be substituted in place of the presilencer, we so not offer (or suggest) this due the unacceptable increase in exhaust noise.
The down pipe is equipped with a mounting flange for the oxygen sensor. This kit includes all necessary mounting hardware, air control & check valve cover plate, and gaskets (3 Replacement Pipe-to-Presilencer gaskets).
| SKU: | 16214 |
EXHAUST PRE-SILENCER WITH DOWN PIPE, 89-92 NON TURBO AUTOMATIC TRANSMISSION
$534.83
Related Products:
-
Exhaust Down Pipe 86-92 Non-Turbo Coupes 2 1/2″
Exhaust Down Pipe 86-92 Non-Turbo Coupes 2 1/2″
This Down Pipe is available for custom applications in a 1986-91 RX-7 (excluding convertible) non-turbo application. This 2.5-inch down pipe fits either manual or automatic transmission equipped cars and eliminates the catalytic converter sections.
This down pipe bolts to the stock exhaust manifold, but the use of our presilencer (or a suitable replacement) is required to connect this assembly to the Y-pipe section. If you need to retain a catalytic converter in your exhaust system, you may find a suitable unit offered in the aftermarket. Although the replacement of your stock catalytic converters with a single aftermarket unit is technically NOT legal, this approach may suit your emissions needs. We suggest you contact your local emissions testing facility for more information. Gaskets sold separately.
SKU: S16206 -
EXHAUST SYSTEM SINGLE, 86-92 NON TURBO WITH RACING BEAT REAR MUFFLERS
Single Exhaust System, 86-92 Non Turbo with Racing Beat Rear Mufflers
SKU: 16-MZTX-0020RB -
EXHAUST PRE-SILENCER, 89-92 NON TURBO AUTOMATIC TRANSMISSION
Racing Beat Exhaust Pre-Silencer, 89-92 Non Turbo Automatic Transmission
SKU: 16409 -
EXHAUST HEADER 13B, 79-92 4&6-PORT DUAL OUTLET
Racing Beat 13B Exhaust Header, 79-92 4&6-PORT DUAL OUTLET
SKU: 16127 Manufacturer SKU: 16127 -
EXHAUST HANGER, 2 SLEEVES
Exhaust Hanger, 2 Sleeves
Go To Our FAQ for Exhaust Hangers to see the locations and part numbers of the hangers for your car.
SKU: 40-1600-1114 Manufacturer SKU: 1114-40-160 -
EXHAUST “Y” PIPE-RACING BEAT, 86-92
Racing Beat Exhaust “Y” Pipe, 86-92
The Racing Beat Y-pipe for the 1986-92 RX-7 (All Models) is a perfect replacement for a failing stock component. The Racing Beat Y-pipe is slightly larger in diameter than the stock non-turbo Y-pipe, and matches the diameter (2.5″ OD) of the stock TURBO II Y-pipe. Therefore, if you are replacing the muffler(s) on a TURBO II application, and unless the original stock Y-pipe is failing, there is no performance benefit to be gained from the addition of this Y-pipe. This Y-pipe includes the Cat-to-Y-pipe gasket. If needed, the Y-pipe outlet gaskets can be purchased separately. Manufactured by Racing Beat using heavy-walled steel tubing and laser cut flanges then finished with a chrome-plated surface coating for excellent durability.
Replacement Rubber Exhaust Hangers
We recommend the replacement of the original rubber exhaust hangers during the installation of any new exhaust component. It is our experience that over time the original rubber hangers can deteriorate, crack, and fail; which can result in the incorrect alignment of the exhaust system.SKU: 16447
You May Also Like:
-
EXHAUST HEADER 12A, 81-83 RX7
Racing Beat 12A Exhaust Header, 81-83 RX7. Actual header not shown in photo – oxygen sensor fitting only included on 1984-85 RX-7 GSL-SE header.
This Racing Beat RX-7 Header is designed for a bolt-on installation, when used with the appropriate Racing Beat Power Pulse Presilencer in all 1981-83 RX-7s. The combination of this RX-7 header and the appropriate presilencer replaces the stock exhaust manifold and all catalytic converters for use on racing applications, along with any intermediate pieces of tubing.
The Racing Beat RX-7 header assembly is constructed with .120-inch wall, mandrel-bend, mild steel tubing for increased durability. The engine-to-header flange is laser-cut from 1/2-inch thick steel plate to ensure positive gas sealing. An outlet gasket is included. An engine-to-header gasket is available separately if needed.
SKU: 16010 -
-
EXHAUST HEADER 13B, 74-78 NO FLANGE EXCEPT PICK UP
Racing Beat 13B Exhaust Header, 74-78 No Flange. Will not work on the Pick Up
This rotary exhaust Header/Collector (less outlet flange) is ideal for RX-2, RX-3, RX-4, and COSMO (does not fit rotary pickup) custom exhaust installations. The flame-cut, .5-inch thick engine flange provides positive sealing and alignment. By integrating the collector with the header we reduce the effort and cost in completing the exhaust system. Engine-to-pipe gaskets are not included but are available separately. An Air Control and Check Valve Cover Plate is required when using this header with a stock intake system.
If the stock resonator is eliminated during installation of this unit, we strongly recommend selecting a Power Pulse Presilencer and installing it in place of the resonator to maintain a pleasant noise level and character.
SKU: 16007 -
MUFFLER UNIVERSAL, POWER PULSE 79-85 RACING BEAT
Racing Beat Universal Power Pulse Muffler, 79-85
In response to numerous requests from customers demanding a very low restriction“street capable” muffler, Racing Beat now offers the Universal Power Pulse PR-Extreme RX-7 Muffler with a 2.75″ OD internal perforated core design to meet the performance demands of high-horsepower ported rotary engines. The Power Pulse PR-Extreme RX-7 Muffler is compatible with all 1979-85 RX-7 muffler rear mounting positions and retains the factory stock appearance; this PR-Extreme RX-7 Muffler includes an inlet of 3″.
The Racing Beat Universal Power Pulse PR-Extreme RX-7 Muffler is manufactured by the same exhaust components manufacturer that has produced the “tried and proven” First Generation RX-7 Power Pulse mufflers (1979-80, 1981-82, and 1984-85) since the mid-1980s. Utilizing a heavy-walled canister shell and extremely durable heat and noise insulating materials, the Racing Beat Power Pulse PR-Extreme RX-7 Muffler is engineered for the high exhaust gas temperatures found in rotary engine applications.
The main body of the muffler canister measures 8 inches in diameter and 18 inches in length. The dual outlet tips are completely chrome-plated with straight-cut outlet.
Now may be the time to consider replacing the old rubber muffler hangers on your RX-7. New replacement hangers will ensure correct alignment of the RX-7 muffler canister and tip position in the bumper opening.
SKU: 16436 -
-
EXHAUST SYSTEM DUAL, 13B DUAL PIPE 79-85
Racing Beat 13B 4 Port Dual Pipe Exhaust System 79-85
Will work on 6 Port if not using the actuators.SKU: 16423