EXHAUST PRE-SILENCER WITH DOWN PIPE, 89-92 CONVERTIBLE AUTOMATIC TRANSMISSION
Racing Beat Exhaust Pre-Silencer with Down Pipe, 89-92 Non-Turbo Automatic Transmission Convertible
Down Pipe with Presilencer – 1989-92 RX-7 Convertible Non-Turbo (equipped w/Auto Transmission) – The 1986-92 13B 6-port engines, in stock form with the factory fuel injection, produces similar power gains with either our Header/Presilencer combo or our RX-7 Down Pipe/Presilencer combination. If you have no intentions of installing RB’s Holley intake System (or any other aftermarket carb set-up), we recommend the use of the RX-7 Down Pipe/Presilencer combo since it offers a slightly quieter exhaust note, is easier to install and less costly. If you are intending to upgrade the intake or fuel injection system, the Header/Presilencer combo offers the greatest performance potential.
The 1989-92 RX-7 down Pipe/Presilencer combination incorporates a 2.5-inch O.D. Down Pipe and our perforated stainless steel core and stainless steel wool-packed Presilencer to boost power approximately 13% – an 18 horsepower increase on a 1987 RX 7- and maintain a comfortable exhaust noise level during full power driving.
The replacement pipe connects to the factory exhaust manifold, and the presilencer connects to the factory Y-pipe, replacing all catalytic converters and intermediate tubing. It is not possible to use just the down pipe to replace only the catalytic converters. The use of the presilencer is required to complete the connection to the y-pipe. Although a short length of tubing can be substituted in place of the presilencer, we do not offer (or suggest) this due the unacceptable increase in exhaust noise.
The down pipe is equipped with a mounting flange for the oxygen sensor. This kit includes all necessary mounting hardware, air control & check valve cover plate, and gaskets (3 Replacement Pipe-to-Presilencer gaskets).
| SKU: | 16218 |
EXHAUST PRE-SILENCER WITH DOWN PIPE, 89-92 CONVERTIBLE AUTO TRANS
$534.83
Related Products:
-
EXHAUST “Y” PIPE-RACING BEAT, 86-92
Racing Beat Exhaust “Y” Pipe, 86-92
The Racing Beat Y-pipe for the 1986-92 RX-7 (All Models) is a perfect replacement for a failing stock component. The Racing Beat Y-pipe is slightly larger in diameter than the stock non-turbo Y-pipe, and matches the diameter (2.5″ OD) of the stock TURBO II Y-pipe. Therefore, if you are replacing the muffler(s) on a TURBO II application, and unless the original stock Y-pipe is failing, there is no performance benefit to be gained from the addition of this Y-pipe. This Y-pipe includes the Cat-to-Y-pipe gasket. If needed, the Y-pipe outlet gaskets can be purchased separately. Manufactured by Racing Beat using heavy-walled steel tubing and laser cut flanges then finished with a chrome-plated surface coating for excellent durability.
Replacement Rubber Exhaust Hangers
We recommend the replacement of the original rubber exhaust hangers during the installation of any new exhaust component. It is our experience that over time the original rubber hangers can deteriorate, crack, and fail; which can result in the incorrect alignment of the exhaust system.SKU: 16447 -
Exhaust Down Pipe 86-92 RX7 Convertibles 2 1/2″
Racing Beat Down Pipe for 86-92 RX7 Convertibles 2 1/2″
This Down Pipe is available for use in a 1988-92 RX-7 Convertible application. This 2.5″ OD Down Pipe bolts directly to the stock exhaust manifold and eliminates all catalytic converters, but the use of our presilencer (or a suitable replacement) is required to connect this assembly to the Y-pipe section. If you need to retain a catalytic converter in your exhaust system, you may find a suitable unit offered in the aftermarket. Although the replacement of your stock catalytic converters with a single aftermarket unit is technically NOT legal, this approach may suit your emissions needs. We suggest you contact your local emissions testing facility for more information. Gaskets sold separately.
SKU: S16209 -
MUFFLER ROAD RACE, 86-92 LEFT (DUAL SYSTEM) RACING BEAT
Racing Beat Road Race Muffler, 86-92 Left (Dual System)
Racing Beat’s Road Race mufflers are intended to bolt-up to the outlets of the Road Race Y-Pipe section (16411) only, and are not compatible with the stock or Racing Beat (16447) y-pipe section. These mufflers can be ordered separately for use in custom applications. With over 25 years of exhaust system production experience, Racing Beat has the ability to match the correct internal muffler canister design to the engine’s exhaust output to provide the optimum combination of sound and performance. This muffler canister is manufactured using 304-stainless steel and features a 2-inch diameter straight-through design for maximum performance gains. Finished with a 3.5-inch polished 304 stainless steel tip, this muffler sounds as good as it looks! All stock hanger positions are retained.
SKU: 16439 -
EXHAUST PRE-SILENCER, 89-92 NON TURBO AUTOMATIC TRANSMISSION
Racing Beat Exhaust Pre-Silencer, 89-92 Non Turbo Automatic Transmission
SKU: 16409 -
EXHAUST SYSTEM DUAL, 89-92 6 PORT RACING BEAT
EXHAUST SYSTEM DUAL, 89-92 6 PORT RACING BEAT Manual Transmission
Racing Beat offers the complete Full Stainless Steel Road Race RX-7 Exhaust System for the 1989-92 RX-7 (manual transmission). This completely Stainless Steel RX-7 exhaust system is intended for use on RX-7 applications running under the extremes of road racing, drag racing, or any high performance, high RPM application. The Racing Beat Full Stainless Steel RX-7 dual exhaust system has been designed to maximize the exhaust gas scavenging benefits while maintaining reasonable sound level outputs.
NOTE: This exhaust system is not compatible for use on automatic transmission-equipped vehicles due to fitting tolerances with the larger AT bell housing.
The following is included in this RX-7 exhaust system:
1989-92 RX-7 Stainless Steel Road Race Header
The Racing Beat Road/Race Header for the 1989-92 13B engine features Stainless Steel construction for excellent durability.Road Race Presilencer
Mating to the outlet of the header is the Racing Beat Road Race Presilencer. The straight-through dual presilencer unit offers beneficial sound reducing qualities by trapping a significant level of the harsh rotary exhaust note.Road Race Y-Pipe
The Racing Beat Y-Pipe section routes the exhaust gases exiting the presilencer section to each of the Power Pulse muffler units.Road Race Mufflers (Left and Right Pair)
Sharing the same design technology as our Power Pulse muffler units, the Road/Race mufflers (Left and Right) feature all stainless steel construction for superior durability and appearance. Large diameter tubing routes the exhaust gas through each muffler unit, exiting through polished stainless steel tips.SKU: 16452 -
MUFFLER ROAD RACE, 86-92 RIGHT (DUAL SYSTEM) RACING BEAT
Racing Beat Road Race Muffler, 86-92 Right Side (Dual System)
Racing Beat’s Road Race mufflers are intended to bolt-up to the outlets of the Road Race Y-Pipe section (16411) only, and are not compatible with the stock or Racing Beat (16447) y-pipe section. These mufflers can be ordered separately for use in custom applications. With over 25 years of exhaust system production experience, Racing Beat has the ability to match the correct internal muffler canister design to the engines exhaust output to provide the optimum combination of sound and performance. This muffler canister is manufactured using 304-stainless steel and features a 2-inch diameter straight-through design for maximum performance gains. Finished with a 3.5-inch polished 304 stainless steel tip, this muffler sounds as good as it looks! All stock hanger positions are retained.
SKU: 16438
You May Also Like:
-
EXHAUST HEADER 13B, 89-92 6PORT DUAL PIPE
Racing Beat 13B Exhaust Header, 89-92 With 6 Port Actuation and O2 sensor fitting.
SKU: 16129 -
EXHAUST HEADER 13B, 74-78 NO FLANGE EXCEPT PICK UP
Racing Beat 13B Exhaust Header, 74-78 No Flange. Will not work on the Pick Up
This rotary exhaust Header/Collector (less outlet flange) is ideal for RX-2, RX-3, RX-4, and COSMO (does not fit rotary pickup) custom exhaust installations. The flame-cut, .5-inch thick engine flange provides positive sealing and alignment. By integrating the collector with the header we reduce the effort and cost in completing the exhaust system. Engine-to-pipe gaskets are not included but are available separately. An Air Control and Check Valve Cover Plate is required when using this header with a stock intake system.
If the stock resonator is eliminated during installation of this unit, we strongly recommend selecting a Power Pulse Presilencer and installing it in place of the resonator to maintain a pleasant noise level and character.
SKU: 16007 -
EXHAUST HANGER, 2 SLEEVES
Exhaust Hanger, 2 Sleeves
Go To Our FAQ for Exhaust Hangers to see the locations and part numbers of the hangers for your car.
SKU: 40-1600-1114 Manufacturer SKU: 1114-40-160 -
-
-
EXHAUST HEADER 12A, 79-85 RX7 DUAL OUTLET
Racing Beat 12A Exhaust Header, 79-85 RX7 Dual Outlet
SKU: 16125