EXHAUST HEADER 13B, 86-88 6 PORT DUAL PIPE
Racing Beat 13B Exhaust Header 86-88 With 6 Port Actuation and O2 Sensor Fitting Dual Pipe
| SKU: | 16128 |
EXHAUST HEADER 13B, 86-88 6 PORT DUAL PIPE
Road Race Header (w/ 6-port intake actuator pick-up tube & exhaust oxygen sensor position for use on a 1986-88 RX-7 13B) – This model Road Race Header that we offer is intended to bolt-up to the Road Race Presilencer section.
Racing Beat Fitting Notes: This header is not compatible with the Street Port Center Section that we offer for the earlier 1984-85 RX-7 GSL-SE – only with the Road Race Presilencer section referenced above. This header is not compatible with the 1988-92 RX-7 convertible chassis equipped with the automatic transmission – the header outlet will make contact with the transmission case.
Racing Beat’s Road Racing Header is the first step in building a serious racing exhaust system. The engine-to-pipe flange is laser cut from 1/2″ thick flat steel for superb exhaust gas sealing qualities. Like all of the rotory headers they manufacture, the Road Racing Header is constructed with 2″ OD mild steel tubing, .120″ wall thickness, and mandrel-bent tubing throughout. This header weighs approximately 15.5 lbs and is approximately 28″ in length.
On the 1986-88 13B 6-Port engines, the auxiliary intake actuators are operated by back pressure from the exhaust system. This header features a back pressure pick-up tube that allows for the correct operation of the 6-port intake actuators. Also included on the header is an oxygen sensor position for cars that require an exhaust oxygen sensor for correct operation.
Outlet flange gaskets, bolts, nuts, AC & CV cover plate, and installation instructions are included. An Engine-to-Header gasket is not included, but is available separately if needed.
$395.36
Related Products:
-
EXHAUST SYSTEM DUAL, 86-88 6 PORT RACING BEAT
Racing Beat Dual Exhaust System, 86-88 6 Port Non Turbo Manual Transmission
Racing Beat offers the complete Full Stainless Steel Road Race RX-7 Exhaust System for the 1986-88 RX-7. This completely Stainless Steel RX-7 exhaust system is intended for use on RX-7 applications running under the extremes of road racing, drag racing, or any high performance, high RPM application. The Racing Beat Full Stainless Steel RX-7 dual exhaust system has been designed to maximize the exhaust gas scavenging benefits while maintaining reasonable sound level outputs.
NOTE: This exhaust system is not compatible with automatic transmission equipped-vehicles due to interference issues with the bell housing.
The following is included in this RX-7 exhaust system:
1986-88 RX-7 Road Race Header
The Racing Beat Road Race Header for the 1986-88 13B 6-Port chassis features stainless steel construction for excellent durability. Also incorporated with this header is the requisite exhaust back-pressure pickup tube, necessary to assure the correct operation of the 6-port intake actuators mounted on the engine. (If you have removed these intake actuators or have rendered them inoperable, you can install the 1989-92 Road Race system instead.)Road Race Presilencer
Mating to the outlet of the header is the Racing Beat Road Race Presilencer. The straight-through dual presilencer unit offers beneficial sound reducing qualities by trapping a significant level of the harsh rotary exhaust note.Road Race Y-Pipe
The Racing Beat Y-Pipe section routes the exhaust gases exiting the presilencer section to each of the Power Pulse muffler units.Road Race Mufflers (Left and Right Pair)
Sharing the same design technology as our Power Pulse muffler units, the Road Race mufflers (Left and Right) feature all stainless steel construction for superior durability and appearance. Large diameter tubing routes the exhaust gas through each muffler unit, exiting through polished stainless steel tips.SKU: 16451 -
MUFFLER ROAD RACE, 86-92 LEFT (DUAL SYSTEM) RACING BEAT
Racing Beat Road Race Muffler, 86-92 Left (Dual System)
Racing Beat’s Road Race mufflers are intended to bolt-up to the outlets of the Road Race Y-Pipe section (16411) only, and are not compatible with the stock or Racing Beat (16447) y-pipe section. These mufflers can be ordered separately for use in custom applications. With over 25 years of exhaust system production experience, Racing Beat has the ability to match the correct internal muffler canister design to the engine’s exhaust output to provide the optimum combination of sound and performance. This muffler canister is manufactured using 304-stainless steel and features a 2-inch diameter straight-through design for maximum performance gains. Finished with a 3.5-inch polished 304 stainless steel tip, this muffler sounds as good as it looks! All stock hanger positions are retained.
SKU: 16439 -
EXHAUST HANGER, 2 SLEEVES
Exhaust Hanger, 2 Sleeves
Go To Our FAQ for Exhaust Hangers to see the locations and part numbers of the hangers for your car.
SKU: 40-1600-1114 Manufacturer SKU: 1114-40-160 -
EXHAUST HANGER, 86-92 @ “Y” PIPE
Exhaust Hanger at “Y” Pipe, 86-92
Go To Our FAQ for Exhaust Hangers to see the locations and part numbers of the hangers for your car.
SKU: 40-060B-N326 Manufacturer SKU: N326-40-060B -
-
EXHAUST PRE-SILENCER, 86-92 DUAL PIPE
Racing Beat Exhaust Pre-Silencer, 86-92 Dual Pipe With Gasket & Hardware
SKU: 16448
You May Also Like:
-
MUFFLER UNIVERSAL, POWER PULSE 79-85 RACING BEAT
Racing Beat Universal Power Pulse Muffler, 79-85
In response to numerous requests from customers demanding a very low restriction“street capable” muffler, Racing Beat now offers the Universal Power Pulse PR-Extreme RX-7 Muffler with a 2.75″ OD internal perforated core design to meet the performance demands of high-horsepower ported rotary engines. The Power Pulse PR-Extreme RX-7 Muffler is compatible with all 1979-85 RX-7 muffler rear mounting positions and retains the factory stock appearance; this PR-Extreme RX-7 Muffler includes an inlet of 3″.
The Racing Beat Universal Power Pulse PR-Extreme RX-7 Muffler is manufactured by the same exhaust components manufacturer that has produced the “tried and proven” First Generation RX-7 Power Pulse mufflers (1979-80, 1981-82, and 1984-85) since the mid-1980s. Utilizing a heavy-walled canister shell and extremely durable heat and noise insulating materials, the Racing Beat Power Pulse PR-Extreme RX-7 Muffler is engineered for the high exhaust gas temperatures found in rotary engine applications.
The main body of the muffler canister measures 8 inches in diameter and 18 inches in length. The dual outlet tips are completely chrome-plated with straight-cut outlet.
Now may be the time to consider replacing the old rubber muffler hangers on your RX-7. New replacement hangers will ensure correct alignment of the RX-7 muffler canister and tip position in the bumper opening.
SKU: 16436 -
EXHAUST HEADER 13B, 74-78 NO FLANGE EXCEPT PICK UP
Racing Beat 13B Exhaust Header, 74-78 No Flange. Will not work on the Pick Up
This rotary exhaust Header/Collector (less outlet flange) is ideal for RX-2, RX-3, RX-4, and COSMO (does not fit rotary pickup) custom exhaust installations. The flame-cut, .5-inch thick engine flange provides positive sealing and alignment. By integrating the collector with the header we reduce the effort and cost in completing the exhaust system. Engine-to-pipe gaskets are not included but are available separately. An Air Control and Check Valve Cover Plate is required when using this header with a stock intake system.
If the stock resonator is eliminated during installation of this unit, we strongly recommend selecting a Power Pulse Presilencer and installing it in place of the resonator to maintain a pleasant noise level and character.
SKU: 16007 -
EXHAUST HEADER 13B, 79-92 4&6-PORT DUAL OUTLET
Racing Beat 13B Exhaust Header, 79-92 4&6-PORT DUAL OUTLET
SKU: 16127 Manufacturer SKU: 16127 -
SPLIT AIR EXHAUST GASKET, —NLA— 79-80 HEAT EXCHANGER FRONT & REAR
Split Air Exhaust Gasket, 79-80 Split Air Pipe To Catalytic Converter
Heat Exchanger Front and RearSorry, this item has been discontinued by Mazda
SKU: 13-135B-8527 Manufacturer SKU: 8527-13-135B -
EXHAUST STUD, RENESIS EXHAUST MANIFOLD TO ENGINE
Exhaust Stud Renesis, Exhaust Manifold to Engine (4 Required)
SKU: 13-708A-SL50 Manufacturer SKU: SL50-13-708A -
