EXHAUST HEAD PIPE, RX7 79-80 —NLA—
EXHAUST HEAD PIPE, RX7 79-80
Sorry, this item has been discontinued by Mazda.
| SKU: | 40-620A-8871 |
| Manufacturer SKU: | 8871-40-620A |
EXHAUST HEAD PIPE, RX7 79-80
$0.00
Related Products:
-
EXHAUST HEAT EXCHANGER GASKET, FRONT 76-80
79-80 Front of Heat Exchanger Gasket
SKU: 40-3050-N2Y1 Manufacturer SKU: N2Y1-40-305 -
EXHAUST CENTER SECTION, 79-85 RACING BEAT 4 PORT/6 PORT
Racing Beat Exhaust Center Section, 79-85 4 Port/6 Port
SKU: 16398 -
ENGINE TO PIPE FLANGE 12A
12A Engine To Pipe Flange 74-85
This 1/2″ thick laser-cut engine-to-header exhuast flange can be used to fabricate a custom exhaust system for any 1974-85 12A rotary engine. This is the same flange that is used on Racing Beat’s 12A engine- headers.
SKU: 16182 -
-
EXHAUST SYSTEM DUAL, 12A DUAL PIPE 79-85
Racing Beat Dual Exhaust System, 12A Dual Pipe 79-85
SKU: 16422 -
EXHAUST GASKET, FRESH AIR PIPE 79-80
Fresh Air Pipe Exhaust Gasket 79-80
SKU: 40-698A-1259 Manufacturer SKU: 1259-40-698A
You May Also Like:
-
EXHAUST HEADER 13B, 74-78 NO FLANGE EXCEPT PICK UP
Racing Beat 13B Exhaust Header, 74-78 No Flange. Will not work on the Pick Up
This rotary exhaust Header/Collector (less outlet flange) is ideal for RX-2, RX-3, RX-4, and COSMO (does not fit rotary pickup) custom exhaust installations. The flame-cut, .5-inch thick engine flange provides positive sealing and alignment. By integrating the collector with the header we reduce the effort and cost in completing the exhaust system. Engine-to-pipe gaskets are not included but are available separately. An Air Control and Check Valve Cover Plate is required when using this header with a stock intake system.
If the stock resonator is eliminated during installation of this unit, we strongly recommend selecting a Power Pulse Presilencer and installing it in place of the resonator to maintain a pleasant noise level and character.
SKU: 16007 -
EXHAUST PRE-SILENCER WITH DOWN PIPE, 88 CONVERTIBLE MANUAL
Racing Beat Exhaust Pre-Silencer with Down Pipe, 88 Convertible Manual Transmission Non-Turbo
Down Pipe with Presilencer – 1988 RX-7 Convertible Non-Turbo (w/Manual Transmission) – The 1986-92 13B 6-port engines, in stock form with the factory fuel injection, produces similar power gains with either our Header/Presilencer combo or our RX-7 Down Pipe/Presilencer combination. If you have no intentions of installing RB’s Holley intake System (or any other aftermarket carb set-up), we recommend the use of the down pipe/Presilencer combo since it offers a slightly quieter exhaust note, is easier to install and less costly. If you are intending to upgrade the intake or fuel injection system, the Header/Presilencer combo offers the greatest performance potential.
The 1988 RX-7 Convertible (w/ Manual Transmission) Down Pipe/Presilencer combination incorporates a 2.5-inch O.D. Down Pipe and our perforated stainless steel core and stainless steel wool-packed Presilencer to boost power approximately 13% – an 18 horsepower increase on a 1987 RX 7- and maintain a comfortable exhaust noise level during full power driving.
The replacement pipe connects to the factory exhaust manifold, and the presilencer connects to the factory Y-pipe, replacing all catalytic converters and intermediate tubing. (The downpipe cannot be used as a “bolt-up” component to replace just the catalytic converters.)
The Racing Beat presilencer is equipped with an exhaust back-pressure tube for correct operation of the 6-port actuators. Installation of this requires the removal of the air control and check valve and the air pump. This kit includes all necessary mounting hardware, air control & check valve cover plate, and gaskets (1 Back Pressure Pick-up and 3 Replacement Pipe-to-Presilencer gaskets).
SKU: 16209 -
-
-
EXHAUST HEADER 13B, 79-92 4&6-PORT DUAL OUTLET
Racing Beat 13B Exhaust Header, 79-92 4&6-PORT DUAL OUTLET
SKU: 16127 Manufacturer SKU: 16127 -
