EXHAUST DOWN PIPE, 87-92 TURBO 3″
Racing Beat Exhaust Down Pipe 87-92 Turbo 3″
SKU: | 16425D |
EXHAUST DOWN PIPE, 87-92 TURBO 3″
The REV TII 3-inch OD stainless steel RX-7 down pipe is a direct replacement for the down pipe in the Racing Beat REV TII Complete RX-7 Exhaust System. This down pipe is intended as a bolt-on component ONLY if used with the Racing Beat REV TII Complete Exhaust System components.
Produced using stainless steel 3-inch OD tubing and flanges, this RX-7 down pipe can also be used for as the lead component in a custom exhaust application. An oxygen sensor fitting is supplied with the downpipe.
$261.95
Related Products:
-
EXHAUST PRE-SILENCER GASKET, RACING BEAT TURBO 3″
Racing Beat Exhaust Pre Silencer Gasket, Turbo 3″
Gasket for 16192 FlageSKU: 16340 -
-
EXHAUST SYSTEM, 86-92 TURBO
Racing Beat Exhaust System, 86-92 Turbo
1987-91 RX-7 TURBO REV II Complete High Performance Exhaust System – If you own a TURBO II RX-7 and you’ve found your way to this webpage, congratulations! Why? Because your search for an exhaust system for your car ends here. Simply put, this is the ultimate exhaust for any Turbo II RX-7!
The REV TII High Performance RX-7 Exhaust is legendary with FC3S owners. This RX-7 exhaust system includes a 3-inch OD REV TII Down Pipe from the turbo outlet that mates to a REV TII Presilencer section. The outlet of the presilencer connects to the inlet of the REV TII Y-Pipe which routes the exhaust gases down two 2.375-inch OD (60mm) pipes into a pair of left and right REV TII Power Pulse Mufflers. Once installed, this bolt-on exhaust system increases horsepower approximately 32% – that’s a 59 HP increase on a 1987 Turbo II RX-7!
The REV TII High Performance RX-7 Exhaust system reduces exhaust gas back-pressure significantly, thereby allowing the un-assisted turbo boost pressure to increase to 10-11 psi. (Note: A fuel cut controller device is required to prevent fuel cutoff to the rear rotor above the factory pre-set limit.)
This bolt-on system uses the stock mounting points for ease of installation. Each system is supplied with all necessary mounting hardware and gaskets. (The kit does not include turbo outlet gasket, if needed it can be ordered separately.) The down pipe section is provided with a position for the oxygen sensor.
SKU: 16425 -
EXHAUST MUFFLER GASKET, USE WITH RACING BEAT 16425 SYSTEM
Exhaust Muffler Gasket, Use with Racing Beat 16425 System
SKU: 16339 -
FLANGE PRE-SILENCER, 3″ STAINLESS
Pre-Silencer Flange, 3″ Stainless
Price listed is for one (1) flange – above photo shows the inlet and sealing sides of a single flange.
SKU: 16185 -
EXHAUST PRE-SILENCER, UNIVERSAL STAINLESS STEEL 3″
Racing Beat Universal Stainless Steel Exhaust Pre-Silencer 3″ id
Racing Beat offers two versions of our 3-inch ID Power Pulse Presilencers for use in the design and manufacture of a custom exhaust system for your street or race vehicle. Well-suited for the demands of high-power turbo applications, the oval-shaped 3-inch ID presilencer can be adapted to fit into tight spaces under your car. Manufactured using 304 stainless steel inside and out, this presilencer unit offers sound reducing performance at a very reasonable price!
The size of this presilencer is: 7.25″ Wide x 4.875″ High x 15.75″ Long.
SKU: 16434