EXHAUST CONVERTER MAIN, 09-11 RX8 MANUAL TRANSMISSION
Catalytic Converter Main, 09-11 RX8 Manual Transmission
| SKU: | 20-55X0-N3Y6 |
| Manufacturer SKU: | N3Y6-20-55X |
Catalytic Converter Main, 09-11 RX8 Manual Transmission
$2,333.21
Related Products:
-
EXHAUST NUT RX8, REAR OF CAT
Exhaust Nut RX8, Rear of Cat (2 Required)
SKU: 01-0030-9994 Manufacturer SKU: 9994-01-003 -
EXHAUST NUT 93-95 TURBO TO MANIFOLD (USES 5) & 04-11 MANIFOLD TO CAT
Exhaust Nut 93-95, Turbo To Manifold (USES 5) 10mm
This nut is also the correct nut for 04-11 RX8 at the front of the catalytic converter to the exhaust manifold
SKU: 40-3550-JE10 Manufacturer SKU: JE10-40-355 -
EXHST CATALYTIC CONVERTER REPLACE PIPE 04-11 RX8
Racing Beat Catalytic Converter Replacement Pipe, 04-11 RX8
Racing Beat REN.V1 RX-8 Race Pipe
Each pipe comes complete with all required mounting hardware, gaskets, and installation instructions.
RX-8 Race Pipe – 2004-2011 RX-8 – Racing Beat offers a full 304-stainless steel catalytic converter replacement pipe for RX-8 racing applications. The weight of this pipe is 10 lbs. This mandrel-bent 3″ OD racing pipe is a direct bolt-on replacement for the stock catalytic converter section. This pipe utilizes a genuine OEM rear mounting flange for a secure fit to the stock (or an aftermarket) exhaust system. (See photo below.) The race pipe is equipped with a sensor fitting for the oxygen sensor. (Note: Placement of the sensor in the pipe will cause the “check engine” light to be illuminated, but performance and engine systems for racing applications will not be affected.) Removal of the OE catalytic converter/presilencer section will result in a noticeably louder exhaust tone.
SKU: 16201 -
EXHAUST STUD RX8, MAIN CAT REAR (EACH)
Exhaust Stud RX8, Main Cat Rear (Each)(2 Required)
SKU: 40-5840-B31R Manufacturer SKU: B31R-40-584 -
EXHAUST SPRING RX8, REAR OF CATALYTIC CONVERTER
Exhaust Spring RX8, Rear of Catalytic Converter (2 Required)
SKU: 40-582A-YJ15 Manufacturer SKU: YJ15-40-582A -
EXHAUST MANIFOLD TO CATALYTIC CONVERTER GASKET, RX8 FRONT
Exhaust Manifold to Catalytic Converter Gasket, 04-11 RX8 Front
SKU: 40-3050-N3H1 Manufacturer SKU: N3H1-40-305
You May Also Like:
-
EXHAUST STUD, RENESIS EXHAUST MANIFOLD TO ENGINE
Exhaust Stud Renesis, Exhaust Manifold to Engine (4 Required)
SKU: 13-708A-SL50 Manufacturer SKU: SL50-13-708A -
EXHAUST PRE-SILENCER WITH DOWN PIPE, 88 CONVERTIBLE MANUAL
Racing Beat Exhaust Pre-Silencer with Down Pipe, 88 Convertible Manual Transmission Non-Turbo
Down Pipe with Presilencer – 1988 RX-7 Convertible Non-Turbo (w/Manual Transmission) – The 1986-92 13B 6-port engines, in stock form with the factory fuel injection, produces similar power gains with either our Header/Presilencer combo or our RX-7 Down Pipe/Presilencer combination. If you have no intentions of installing RB’s Holley intake System (or any other aftermarket carb set-up), we recommend the use of the down pipe/Presilencer combo since it offers a slightly quieter exhaust note, is easier to install and less costly. If you are intending to upgrade the intake or fuel injection system, the Header/Presilencer combo offers the greatest performance potential.
The 1988 RX-7 Convertible (w/ Manual Transmission) Down Pipe/Presilencer combination incorporates a 2.5-inch O.D. Down Pipe and our perforated stainless steel core and stainless steel wool-packed Presilencer to boost power approximately 13% – an 18 horsepower increase on a 1987 RX 7- and maintain a comfortable exhaust noise level during full power driving.
The replacement pipe connects to the factory exhaust manifold, and the presilencer connects to the factory Y-pipe, replacing all catalytic converters and intermediate tubing. (The downpipe cannot be used as a “bolt-up” component to replace just the catalytic converters.)
The Racing Beat presilencer is equipped with an exhaust back-pressure tube for correct operation of the 6-port actuators. Installation of this requires the removal of the air control and check valve and the air pump. This kit includes all necessary mounting hardware, air control & check valve cover plate, and gaskets (1 Back Pressure Pick-up and 3 Replacement Pipe-to-Presilencer gaskets).
SKU: 16209 -
EXHAUST SYSTEM DUAL, 12A DUAL PIPE 79-85
Racing Beat Dual Exhaust System, 12A Dual Pipe 79-85
SKU: 16422 -
-
EXHAUST HEADER 12A, 79-85 RX7 DUAL OUTLET
Racing Beat 12A Exhaust Header, 79-85 RX7 Dual Outlet
SKU: 16125 -
Reviews
There are no reviews yet.