EXHAUST CATALYTIC CONVERTER REPLACEMENT PIPE, 04-ON RX8 RESONATED
Racing Beat Catalytic Converter Resonated Replacement Pipe, 04-11 RX8
Racing Beat REN.V2 RX-8 Race Pipe
Resonated Catalytic Converter Replacement Race Pipe – RX-8 owners have discovered that a installing a non-resonated catalytic converter race pipe on a RX-8 can produce a surprising loud exhaust tone. If your racing application or local track requires a modest, quieter exhaust tone, then the Racing Beat REN.V2 resonated race pipe is the perfect solution.
Racing Beat offers a 3″ OD fully stainless steel catalytic converter replacement pipe with dual resonators for RX-8 racing applications. Fitted with two (2) rotary-designed resonator units selected specifically for the RX-8 chassis. Each resonator is tightly packed with stainless steel wool for optimum sound supression and tone quality.
Both our resonated and non-resonated pipe versions are direct bolt-on replacements for the stock catalytic converter section. Racing Beat replacement pipes utilize a genuine Mazda OEM rear mounting flange to ensure a secure fitment to the stock (or an aftermarket) exhaust system. Each replacement pipe is equipped with a sensor fitting for the oxygen sensor. (Note: Placement of the sensor in the pipe will cause the “check engine” light to be illuminated, but performance and engine systems for racing applications will not be affected.)
Each race pipe comes complete with all required mounting hardware, gaskets, and installation instructions.
| SKU: | 16221 |
EXHAUST CATALYTIC CONVERTER REPLACEMENT PIPE, 04-ON RX8 RESONATED
$491.17
Related Products:
-
EXHAUST MUFFLER GASKET, 04-11 RX8 PIPE to CATALYTIC CONVERTER
Exhaust Muffler Gasket, 04-11 RX8 Muffler Pipe to Catalytic Converter
SKU: 40-5810-L315 Manufacturer SKU: L315-40-581 -
EXHAUST CATALYTIC CONVERTER REPLACE PIPE 04-11
Racing Beat Catalytic Converter Replace Pipe, 04-11
Racing Beat REN.V1 RX-8 Race Pipe
Each pipe comes complete with all required mounting hardware, gaskets, and installation instructions.
RX-8 Race Pipe – 2004-2011 RX-8 – Racing Beat offers a full 304-stainless steel catalytic converter replacement pipe for RX-8 racing applications. The weight of this pipe is 10 lbs. This mandrel-bent 3″ OD racing pipe is a direct bolt-on replacement for the stock catalytic converter section. This pipe utilizes a genuine OEM rear mounting flange for a secure fit to the stock (or an aftermarket) exhaust system. (See photo below.) The race pipe is equipped with a sensor fitting for the oxygen sensor. (Note: Placement of the sensor in the pipe will cause the “check engine” light to be illuminated, but performance and engine systems for racing applications will not be affected.) Removal of the OE catalytic converter/presilencer section will result in a noticeably louder exhaust tone.
SKU: 16201 -
EXHAUST O2 SENSOR WELD ON BUNG
Exhaust O2 Sensor Weld On Bung
Browse our Haltech Section
SKU: HT-010702 -
MUFFLER UNIVERSAL STAINLESS 3.5″ RACING BEAT
Racing Beat Universal Stainless 3.5″ Muffler
Power Pulse Race Muffler – 3.5″ ID – 304 Stainless Steel – This all new race muffler was developed in mind for the high horsepower engines requiring maximum flow with sound reducing performance. Constructed from 304 stainless and packed with stainless/ceramic wool, this muffler designed to hold up to the extreme temperatures of the rotary engine.
We strongly suggest incorporating the Power Pulse race presilencer unit in your custom exhaust system to further reduce the exhaust tone produced by the rotary engine.
SKU: 16034 -
FLANGE PRE-SILENCER, 3″ STAINLESS
Pre-Silencer Flange, 3″ Stainless
Price listed is for one (1) flange – above photo shows the inlet and sealing sides of a single flange.
SKU: 16185 -
MUFFLER RX8, RACING BEAT “RACE”
MUFFLER RX8, RACING BEAT “RACE”
Power Output
Performance gains are comparable with Racing Beat REV 8 Street Exhaust:Stock production engine – with muffler removed +5 HP
Stock production engine – with RB street or race exhaust + 3.5 HP approx.Sound Quality
While louder than the stock system, particularly under full throttle, this exhaust system can be used for those looking for a very aggressive exhaust tone for their daily-driven RX-8. A modest driving technique will produce a moderate and tolerable exhaust tone, but jump on the throttle and this exhaust really comes to life. Full throttle does not produce a buzzy or harsh, but a more exotic sound like that of a tuned V-6 engine. During a long-distance trip to the race track during prototype testing for this system, our independent test driver commented that highway cruising was very tolerable, without any droning sounds or harmonics.This exhaust system is equipped with a stainless steel connecting pipe and all required mounting hardware.
*Measured approximately 50′ away from the side of an otherwise stock 2004 RX-8 MT under full throttle. Your actual decibel reading may vary. Other factors, including atmospheric conditions, additional performance accessories, tires, etc.. may cause variations in your actual sound measurement.
SKU: 16396
You May Also Like:
-
-
-
-
-
EXHAUST SYSTEM DUAL, 12A DUAL PIPE 79-85
Racing Beat Dual Exhaust System, 12A Dual Pipe 79-85
SKU: 16422 -
EXHAUST HEADER 13B, 74-78 NO FLANGE EXCEPT PICK UP
Racing Beat 13B Exhaust Header, 74-78 No Flange. Will not work on the Pick Up
This rotary exhaust Header/Collector (less outlet flange) is ideal for RX-2, RX-3, RX-4, and COSMO (does not fit rotary pickup) custom exhaust installations. The flame-cut, .5-inch thick engine flange provides positive sealing and alignment. By integrating the collector with the header we reduce the effort and cost in completing the exhaust system. Engine-to-pipe gaskets are not included but are available separately. An Air Control and Check Valve Cover Plate is required when using this header with a stock intake system.
If the stock resonator is eliminated during installation of this unit, we strongly recommend selecting a Power Pulse Presilencer and installing it in place of the resonator to maintain a pleasant noise level and character.
SKU: 16007
