83-92 NON-TURBO Diameter MAZDATRIX ALUMINUM FLYWHEEL
83-92 NON-TURBO Diameter MAZDATRIX ALUMINUM FLYWHEEL
Mazdatrix designed aluminum flywheel.
With our flywheel the pressure plate bolts directly to the flywheel and uses the original style locating dowels, eliminating the need for separate spacers.
Comes with all necessary hardware.
Flywheel is 11 3/4″ Diameter which fits ALL Non-Turbo Transmissions from ~1974-1991. It uses a 225mm CLUTCH which is standard from ’83 – 1991.
Weight is 7.6 POUNDS with hardware w/o counterweight.
Rear counterweight must be purchased separately to match the engine
Can be used on all 74-82 engines originally equipped with a 215mm clutch, but you must buy a 225mm 83-92 clutch.
Lighter than other ALUMINUM flywheels at 7.6 pounds versus theirs at 8.5 pounds.
| SKU: | 104806-11 |
| Manufacturer SKU: | 104806-11 |
83-92 NON-TURBO Diameter MAZDATRIX ALUMINUM FLYWHEEL
$463.00
Related Products:
-
CLUTCH KIT STAGE 1, 83-92 NON TURBO
Clutch Kit Stage 1, 83-92 Non Turbo
Street/Strip performanceSKU: 10806 Manufacturer SKU: 10806 -
CLUTCH KIT STAGE 2, 83-92 NON-TURBO
Clutch Kit Stage 2, 83-92 Non-Turbo
Race performanceExedy Stage 2
Race performance, Metal Puck Disc and Upgraded Pressure Plate
Includes Disc, Pressure Plate, T/O Bearing, Pilot Bearing and seal, and Alignment ToolWe open every Exedy Kit to make sure that the correct Pilot Bearing and seal are included, due to Exedy rarely includes the pilot seal and sometimes has the incorrect bearing.
SKU: 10954 Manufacturer SKU: 10954 -
-
REAR COUNTERWEIGHT, 13B 86-88
Rear Counterweight, 13B 86-88
SKU: 11-52X0-N3Y8 Manufacturer SKU: N3Y8-11-52X -
REAR COUNTERWEIGHT, 13B 74-85
Rear Counterweight, 13B 74-85
SKU: 11-751A-1029 Manufacturer SKU: 1029-11-751A -
REAR COUNTERWEIGHT 83-85 12A
Rear counterweight for 83-85 12A Engines — they have the “N” on the rotors
These were discontinued by Mazda — We are having them made.
We took a few pair of 83-85 12A rotors, weighed them all for an average, set the bobweights for those weights on a 12A eccentric shaft then we re-balance NEW 13B rear counterweights to match.
SKU: 11-751A-N226-MOD Manufacturer SKU: N226-11-751A-MOD
You May Also Like:
-
TRANS FRONT COVER 81-85 12A THIN BEARING–NLA–
Transmission Front Cover, 81-85 12A (Thin Bearing)
5-spd (use with 81+ front bearing)Sorry, this item has been discontinued by Mazda
SKU: 16-220D-8540 Manufacturer SKU: 8540-16-220D -
CLUTCH FORK BOOT 86-92 TURBO
Clutch Fork Boot 86-92 Turbo
SKU: 16-2140-N302 Manufacturer SKU: N302-16-214 -
CLUTCH SLAVE HOSE, 04-11 HARD @ MASTER
Clutch Slave Hardline Hose, 04-11 RX8 @ Master
SKU: 45-510A-FE05 Manufacturer SKU: FE05-45-510A -
-
BELLHOUSING BOLT, LOWER RIGHT 72-92
Lower Right Bell Housing Bolt 72-92
SKU: 41-0400-9978 Manufacturer SKU: 9978-41-040 -
CLUTCH DISC RACE, ALL ROTARY -82
Racing Beat Race Clutch Disc, All Rotary up to 82, 4 puck
The 4-Puck 215mm Race Clutch Disc is designed for drag and road race use with all 1971-82 12A & 13B Applications (except Rotary Pick-Up). The disc incorporates four (4) sintered copper pucks and a rigid hub for quick, positive engagement, greater fatigue resistance, and improved heat dissipation. The sharpened engagement/disengagement characteristics of this disc require careful driver attention – this disc is not intended for street use.
Time Saving Tip: We strongly recommend replacing the throw-out bearing during any clutch work to ensure trouble free performance. Also, we recommend replacing the transmission front and rear seal kit when re-installing the transmission to reduce the possibility of leakage.
Safety Note: None of the Racing Beat, Exedy, Mazda OE, or any aftermarket flywheel or clutch replacement components should ever be allowed to exceed 10,500 RPM under any condition. You must use an engine RPM-limiter to prevent excessive RPM. If your engine is capable of exceeding 8,500 RPM you must install a transmission scatter shield or ballistic blanket. Failure to implement the above may result in serious injury or even death.
Actual disc not shown in photo.
SKU: 12521