Weber DCOE Parts
-
HEATSHIELD, 74-95 ALL 12A & 13B
Heatshield, 74-95 All 12A & 13B
Click Here for a Weber 48IDA Suggested Parts List
Browse our Weber Carbs, Manifolds and Parts section
SKU: 16219 -
THERMOSTAT GASKET, ALL 70-88 + Weber DCOE BASE
Thermostat Gasket, All up to 88, +Weber DCOE Base Gasket
Browse our Weber Carbs, Manifolds and Parts section
Browse our Water Cooling System parts section.
SKU: 15-173A-1757 Manufacturer SKU: 1757-15-173A -
WEBER ACCELERATOR PUMP BYPASS, NO HOLE “0”
Weber Accelerator Pump Bypass, No Hole “0”
Browse our Weber Carbs, Manifolds and Parts section
SKU: 79701.000 -
WEBER AIR HORN LOCK TAB
Weber Air Horn Lock Tab
Browse our Weber Carbs, Manifolds and Parts section
SKU: 52150.015 -
WEBER BASE GASKET SET DCOE, SOFTMOUNT (PAIR)
Weber DCOE Base Gasket Set, Softmount (Pair)
Browse our Weber Carbs, Manifolds and Parts sectionSKU: 99005.145 -
Weber DCOE Accelerator Pump Jet – Choose-a-Size
Weber DCOE Accelerator Pump Jet
All of the sizes we carry are listed hereBrowse our Weber Carbs, Manifolds and Parts section
SKU: 76801 -
Weber DCOE Idle Fuel Jet – Choose-A-Size
Weber DCOE Idle Fuel Jet
All of the sizes we carry are listed here.Browse our Weber Carbs, Manifolds and Parts section
SKU: 74822 Weber Idle Gas Jet -
WEBER FLOAT NEEDLE and SEAT DCOE, 3.0 MM
Weber Float Needle and Seat DCOE, 3.0 mm
Browse our Weber Carbs, Manifolds and Parts section
SKU: 79503.300 -
Weber Gasket – DCOE Air Filter
Weber DCOE Air Filter Gasket
Browse our Weber Carbs, Manifolds and Parts section
SKU: 99005.030 -
WEBER GASKET SET, ALL DCOE
Weber Gasket Set, All DCOE
Browse our Weber Carbs, Manifolds and Parts section
SKU: 92.0015.05 -
WEBER IDLE SPEED SCREW
Weber Idle Speed Screw
Spring is not included. It is 47600.007Browse our Weber Carbs, Manifolds and Parts section
SKU: 64625.012 -
WEBER INLET FITTING, AN -6 TO WEBER 12MM
-6 To Weber 12mm Inlet Fitting
All Weber IDA carbs come with a useless banjo fitting we have never figured out how to use (unless you tap it 1/8-pipe and use a “barb” fitting). This will replace the stock inlet fitting with -6AN so you can use braided hose.
The 12mm Stat-O-Seal is strongly recommended for this fitting — it is at: WEBER INLET SEAL, STAT-O-SEAL FOR 12MM
We also have a 90° fitting for 8mm / 5/16″ push on hose at: WEBER INLET FITTING for 8mm (5/16″) push on hoseClick Here for a Weber 48IDA Suggested Parts List
Browse our Weber Carbs, Manifolds and Parts section
SKU: 30606-M12D -
WEBER INLET SEAL, STAT-O-SEAL FOR 12MM
Weber Inlet Seal, Stat-O-Seal FOR 12mm
This is the seal needed for the -6AN fuel inlet fitting for Weber carbs.Click Here for a Weber 48IDA Suggested Parts List
Browse our Weber Carbs, Manifolds and Parts section
SKU: 357-12MM-STAT -
WEBER NUT 8X1.25 WITH 10MM HEX
Weber Nut 8X1.25 With 10mm Hex
These are needed for the larger bore carbs as there is not enough room to get a 12mm wrench correctly on the base nuts.
These use a 10mm wrench which gives you room to tighten the nut.
Hard to find in “not jet nut” style and in steel. They can come in handy in many other places also.Click Here for a Weber 48IDA Suggested Parts List
Browse our Weber Carbs, Manifolds and Parts section
SKU: 967-NUT -
WEBER SHAFT LOCK TAB
Weber Shaft Lock Tab Washer Fits IDA or DCOE Sold Each
Part can be referenced at #26
Browse our Weber Carbs, Manifolds and Parts section
SKU: 55520.004 Manufacturer SKU: 55520.004 -
WEBER SHAFT NUT
Weber Shaft Nut Fits IDA or DCOE Sold Each
Part can be referenced at #25
Browse our Weber Carbs, Manifolds and Parts section
SKU: 34710.003 -
WEBER SHAFT WASHER
Weber Shaft Washer Fits IDA or DCOE Sold Each
Reference part at #27
Browse our Weber Carbs, Manifolds and Parts section
SKU: 99024.258 -
WEBER SPRING for EITHER IDLE SPEED OR MIXTURE SCREW
Weber Spring for Either Idle Speed or Mixture Screw
Browse our Weber Carbs, Manifolds and Parts section
SKU: 47600.007 -
WEBER STUD, 8X1.25 35MM
Weber Stud, 8X1.25 35mm
Click Here for a Weber 48IDA Suggested Parts List
Browse our Weber Carbs, Manifolds and Parts section
SKU: AV11981 -
WEBER STUD, 8X1.25 45MM
Weber Stud, 8X1.25 45mm
Most of the Weber Manifolds do not include studs to hold the carb to the manifold. These 45mm ones work great when you are using spacers — measure to be sure these are what you need – depends on the spacer thickness.Browse our Weber Carbs, Manifolds and Parts section
SKU: AV11983