Holley Parts
-
AIR FILTER HOUSING, RACING BEAT HOLLEY WITHOUT FILTER
Racing Beat Air Filter Housing Without Filter for Racing Beat Holley Carburetor
Racing Beat’s dyno-proven Power Pulse Air Filter Assembly, for the Holley Carburetor, is designed specifically for performance. While the assembly uses the same Racing Beat foam air filter element that fits the stock canister, the design of the Power Pulse canister both improves air flow into the carburetor and limits the introduction of dirt particles into the filter element. The spun aluminum canister pieces are powder-coated white for added durability.
The Power Pulse Air Filter Assembly fits most Holley 465, 550, 600, and 650 CFM carburetors (specifically, all Racing Beat Holley Intake System Kits). There is no provision for emission control valve hose/air pump hose connections on this assembly; however, there is a position available to connect a crankcase breather tube if needed.
SKU: 16530 -
HEATSHIELD, 74-95 ALL 12A & 13B
Heatshield, 74-95 All 12A & 13B
Click Here for a Weber 48IDA Suggested Parts List
Browse our Weber Carbs, Manifolds and Parts section
SKU: 16219 -
HOLLEY 12A BRIDGE PORT, —NLA—
HOLLEY 12A BRIDGE PORT
Sorry, this item has been discontinued.
SKU: C-HOLLEY-12A-BP -
HOLLEY 12A STOCK, 76-85 NO PORT —NLA—
Sorry, this item has been discontinued.
Racing Beat Holley Stock port 12A 76-85 (465cfm carb)
Complete Ready-to-Install Kit
One of most significant benefits of this complete ready-to-go kit is that is takes all the guesswork, trial-and-error, and frustration out of attempting to assembly your own intake kit! We’ve taken over 40 years of our rotary engine experience and know-how and combined it for you in this complete, ready-to-install kit. Our intake kits has been thoroughly developed and tested using our in-house engine dyno to ensure maximum performance for each specific engine application.Rotary-tuned By Racing Beat
The heart of each intake system is a performance-proven 4-barrel Holley carburetor. Depending on the requirements of each specific application, the carburetor is disassembled by Racing Beat’s carburetor technicians then reworked, retuned, and reconfigured specifically for use with a designated rotary engine application. This process is not a simple “re-jetting” project, but a complex series of steps requiring machining, drilling and reconfiguring of the main and metering bodies, adjustment of the float bowls, and complete replacement of all jets. Each application has been fully developed and tested on our in-house dyno facility to ensure maximum performance.Each comprehensive package includes a Racing Beat cast-aluminum high-rise intake manifold with a vacuum source for power brakes, a Racing Beat-modified Holley carburetor (465 CFM), foam air cleaner and canister assembly, throttle and metering oil pump linkages, and appropriate gaskets. All emissions control fittings are eliminated. This carburetor includes a vacuum-operated choke.
Performance
When installed on a 1976-78 RX-3 or a 1979-85 RX-7 12A engine, this kit increases engine output by approximately 20 HP with the stock exhaust system. However, for increased performance gains we strongly recommend the installation of an exhaust header/presilencer/Power Pulse Muffler combo (10+ HP) or an open exhaust (15+ HP) – resulting in total performance gains of between 30-35 HP depending on your specific intake/exhaust configuration..SKU: 18009 -
HOLLEY 12A STREET PORT, 76-85 —NLA—
Sorry, this item has been discontinued
Racing Beat Holley, 76-85 Street port 12A (465 cfm carb)
Complete Ready-To-Install Kit
One of most significant benefits of this complete ready-to-go kit is that is takes all the guesswork, trial-and-error, and frustration out of attempting to assembly your own intake kit! Racing Beat has taken over 40 years of their rotary engine experience and know-how and combined it for you in this complete, ready-to-install kit. Racing Beat’s intake kits has been thoroughly developed and tested using their in-house engine dyno to ensure maximum performance for each specific engine application.Rotary-tuned By Racing Beat
The heart of each intake system is a performance-proven Holley carburetor. Depending on the requirements of each specific application, the carburetor is disassembled by Racing Beat’s carburetor technicians then reworked, retuned, and reconfigured specifically for use with a designated rotary engine application. This process is not a simple “re-jetting” project, but a complex series of steps requiring machining, drilling and reconfiguring of the main and metering bodies, adjustment of the float bowls, and complete replacement of all jets.Each comprehensive package includes a Racing Beat cast-aluminum high-rise intake manifold with a vacuum source for power brakes, a Racing Beat-modified Holley carburetor (465 CFM), foam air cleaner and canister assembly, throttle and metering oil pump linkages, and appropriate gaskets. All emissions control fittings are eliminated. This carburetor includes a vacuum-operated choke. The Racing Beat Kit for the Street Port engine includes the same basic components as our non-ported engine Holley Kits (P/N 18009); however, the specific internal modifications to the 465 CFM carburetor are significantly different.
Each comprehensive package includes a cast aluminum high-rise intake manifold with a vacuum source for power brakes, a Racing Beat-modified Holley carburetor (465 CFM), foam air cleaner and canister assembly, throttle and metering oil pump linkages, and appropriate gaskets. All emissions control fittings are eliminated.
Exhaust headers must be used with this street port intake system to achieve maximum horsepower gains.
SKU: 18034 -
HOLLEY 13B 4 PORT STOCK, EARLY NO PORT
Holley Stock port 13B 76-78 (465cfm carb) Discontinued
We offer the popular Racing Beat-modified High Performance Holley Intake System Kit for the 1974-1985 13B 4 Port, stock port (non-ported) engines. Our Racing Beat -modified Holley Intake Systems, manufactured for more than 30 years, have established themselves as an ideal way to increase the horsepower of the 13B rotary engine at a very economical price. With an open header installed in conjunction with the Holley Intake System on the engine, power gains of 40 HP are typical.
Racing Beat’s High Performance Holley Intake System Kit has proven over the years to be an extremely reliable carburetor upgrade, with very “streetable” engine smoothness and drivability characteristics. Fuel economy is comparable to the stock carburetor under similar driving conditions.
One of most significant benefits of this complete ready-to-go kit is that is takes all the guesswork, trial-and-error, and frustration out of attempting to assembly your own intake kit! We’ve taken over 40 years of our rotary engine experience and know-how and combined it for you in this complete, ready-to-install kit. Our intake kits has been thoroughly developed and tested using our in-house engine dyno to ensure maximum performance for each specific engine application.
The heart of each intake system is a performance-proven Holley carburetor. Depending on the requirements of each specific application, the carburetor is disassembled by Racing Beat’s carburetor technicians then reworked, retuned, and reconfigured specifically for use with a designated rotary engine application. This process is not a simple “re-jetting” project, but a complex series of steps requiring machining, drilling and reconfiguring of the main and metering bodies, adjustment of the float bowls, and complete replacement of all jets.
Complete Kit – Ready to Install
Each comprehensive package includes a Racing Beat cast-aluminum high-rise intake manifold with a vacuum source for power brakes, a Racing Beat-modified Holley carburetor (465 CFM), Racing Beat Power Pulse Air Filter Canister with foam filter, throttle and metering oil pump linkages, and appropriate gaskets. All emissions control fittings are eliminated. This carburetor includes a vacuum-operated choke.Note: Installation of this kit requires use of a high performance fuel pump delivering 6 psi @ 20 gph.
SKU: 18017 -
HOLLEY 13B 6-PORT, 84-92
HOLLEY 13B 6-PORT, 84-92 (uses 600cfm carb.)
We offer a Racing Beat-engineered and modified Holley Carburetor Intake Kit for all 1984-92 13B Stock Port (non-ported) 6-Port engines. Racing Beat-Modified High Performance Holley Intake Systems, manufactured for more than 30 years, have established themselves as an ideal way to increase the horsepower output of the 13B rotary engine at a very economical price. This is especially advantageous when compared to the alternative: expensive replacement fuel injection systems with their required software, hardware, and increased complexity.
These carburetor intake kits are a popular and economical alternative for a failed fuel injection system on a stock engine. The complete kit includes an extensively modified 600 CFM Holley “Double Pumper” carburetor (mechanical secondary & manual choke), a Racing Beat cast aluminum intake manifold, the popular Racing Beat Power Pulse Air Filter Canister with filter, basic throttle and metering oil pump linkages (1984-88 applications), gaskets, and detailed installation instructions.
Tuned By Racing Beat
The delivered-new, Holley 600 CFM carburetor included in this kit has been extensively disassembled and re-built at the Racing Beat facility in order to optimize the power output for the 13B 6-port application. One of most significant benefits of our complete ready-to-go kit is that is takes all the guesswork, trial-and-error, and frustration out of attempting to assemble, let alone tune, your own intake kit! We’ve taken over 40 years of our rotary engine experience and know-how and combined it for you in this complete, ready-to-install kit. Our intake kit has been thoroughly developed and tested using our in-house engine dyno to ensure maximum performance for each specific engine application.Depending on your application, you may need to fabricate or purchase specific components to complete installation for your particular application. We suggest you review the 18045 Holley 6PI Kit Instructions to review the installation process. This kit does not make provisions for the operation of the Mazda-installed cruise control unit.
Fuel Pump
You will need to purchase and install a fuel pump that provides a 6 PSI delivery with a minimum 20 GPH rating – selection will depend largely on installation location. The stock fuel pump unit is designed to provide high pressure (40+ PSI) for a fuel injected intake and is not compatible with this carburetor application. It is NOT recommended that a fuel regulator be used to reduce the stock fuel pump pressure to 6 PSI – the stock pump will fail. We recommend the Mallory 4070M fuel pump for this application.1984-85 GSL-SE – The stock fuel pump on this chassis is externally mounted (outside of the fuel tank) and must be replaced with a suitable unit and the appropriate fuel line fittings.
1986-92 (All models) – The fuel pump on this chassis is mounted internally in the fuel tank. The pump must be replaced with an appropriate internally mounted unit, or an external pump configuration must be designed and fabricated. (Moderate fabrication skills are required for this conversion.)
Exhaust
Optimum performance from the installation of this kit requires that a performance exhaust system be installed on the vehicle. The following exhaust configurations are ranked in order of performance potential:1. Long primary header – dual-tube connecting pipe – rear muffler(s). (i.e. Road/Race Exhaust System)
2. Streetable Header/Presilencer – y-pipe – rear mufflers.
3. Downpipe/Presilencer – y-pipe – rear mufflers.This intake kit is not intended for use on applications that retain the catalytic converters and stock exhaust system. If the stock exhaust system is retained, horsepower, throttle response, and performance will be compromised.
SKU: 18045 -
HOLLEY 13B BRIDGE PORT, 13B 4PORT 74-78 BRIDGE
Holley 13B Bridge Port, 13B 4PORT 74-78
Bridgeport 13B (uses 650 cfm carb.)SKU: 18042 -
HOLLEY 13B STREET PORT, 4 PORT
Holley Street Port 13B 4 Port (uses 600 cfm carb.)
InstructionsSKU: 18038 -
HOLLEY 13B STREET PORT, 86-92 TURBO
HOLLEY 13B STREET PORT, 86-92 TURBO
Performance Features
The engine prepared by Racing Beat, in developing this kit, included the 1989-91 Non-Turbo Rotors, with the higher 9.7:1 compression ratio; however, there is little difference in peak horsepower between the lower compression Turbo II rotors and the higher compression Non Turbo Rotors. The use of the TURBO II rotors, and 1 to 2 degrees more advance, would give nearly the same horsepower output. Furthermore, we installed the 1981-85 electronic distributor and coils to dramatically simplify the ignition operation. Because the development engine was assembled with the Mazda OEM apex seals, we deliberately limited the engine to 8800 rpm. With the installation of either carbon or ceramic apex seals, race-clearanced and snap-ringed rotors, and increased bearing clearances, the engine would be capable of running up to 9300 rpm safely and still making excellent power at this level.One of most significant benefits of our complete ready-to-go kit is that is takes all the guesswork, trial-and-error, and frustration out of attempting to assemble, let alone tune, your own intake kit! We’ve taken over 40 years of our rotary engine experience and know-how and combined it for you in this complete, ready-to-install kit. Our intake kit has been thoroughly developed and tested using our in-house engine dyno to ensure maximum performance for each specific engine application.
Complete Kit
The heart of every RX-7 Holley intake kit is a Racing Beat-modified, performance-proven Holley 600 CFM Double-Pumper carburetor. We start with brand new Holley carburetor bodies that are disassembled by Racing Beat’s carburetor technicians and extensively modified in-house for use with a designated rotary engine application. This process is not a simple “re-jetting” project, but rather a complex series of steps requiring machining, drilling, and reconfiguring of the carburetor body itself as well as the primary and secondary metering bodies, adjustment of the float bowls, and complete replacement and/or re-drilling of all jets.Every RX-7 Holley intake kit includes a Racing Beat cast-aluminum high-rise intake manifold with a vacuum source for power brakes, a Racing Beat-modified Holley carburetor, foam air cleaner, and canister assembly, throttle and metering oil pump linkages, and appropriate gaskets. All emissions control fittings are eliminated.
SKU: 18046 -
HOLLEY CARBURETOR ONLY, 12A 465 CFM RACING BEAT MODIFIED
Racing Beat Holley Carburetor Only Stock port 12A 76-85 (465cfm carb) Discontinued
Sorry, this item has been discontinued by the Manufacturer
We offer the extremely popular Racing Beat-modified High Performance Holley carburetor – 465cfm body – for the 1976-85 12A Non-Ported engine application. This carburetor body is the same modified component that is included in our complete 1976-85 12A Non-Ported engine kit. The optional air cleaner assembly and manifold shown are not included, but are available with the complete kit, or as separate items.
Each carburetor is modified by Racing Beat to maximize the performance of a specific engine application. Every carburetor is disassembled, modified and reworked by a Racing Beat carburetor technician. These modifications are the results of countless hours of engine dyno testing and real-world testing. These extensive modifications are undertaken to increase the airflow to meet the demands of the rotary engine.
This carburetor requires the use of a high performance fuel pump delivering 6 psi @ 20 gph, we suggest the use of the Mallory 4070M unit.
SKU: 16634 -
HOLLEY CARBURETOR ONLY, 12A STREET PORT 465CFM RACING BEAT MODIFIED
Racing Beat Modified Holley Carburetor Only, 12A Street Port 465CFM Discontinued
Sorry, this item has been discontinued by the Manufacturer
We offer the extremely popular Racing Beat-modified High Performance Holley carburetor – 465cfm body – for the 1976-85 12A Street-Ported engine application. This carburetor body is the same modified component that is included in our complete 1976-85 12A Street-Ported engine kit. The optional air cleaner assembly and manifold shown are not included, but are available with the complete kit, or as separate items.
Each carburetor is modified by Racing Beat to maximize the performance of a specific engine application. Every carburetor is disassembled, modified and reworked by a Racing Beat carburetor technician. These modifications are the results of countless hours of engine dyno testing and real-world testing. These extensive modifications are undertaken to increase the airflow to meet the demands of the rotary engine.
This carburetor requires the use of a high performance fuel pump delivering 6 psi @ 20 gph, we suggest the use of the Mallory 4070M unit
SKU: 16636 -
HOLLEY CARBURETOR ONLY, 13B 4 PORT STREET PORT 600 CFM RACING BEAT MODIFIED
Racing Beat Modified Holley Carburetor Only, Street port 13B 4-Port (uses 600 cfm carb.)
Racing Beat’s Holley Intake Kit for the 1974-85* 13B 4-Port Street Port engine has proven over the years to be an extremely reliable carburetor upgrade, with very “streetable” engine smoothness and drivability characteristics. We offer the carburetor included with this kit seperately for those looking for a replacment for the orignal Racing Beat-modified unit. The carburetor we supply for the 13B 4-Port Street Port applications features a 600 CFM model utilizing a mechanical choke and mechanical secondaries. As supplied, this carburetor does not include the mounting and attachment hardware that was originally supplied with the complete kit.
The heart of each intake system is a performance-proven Holley carburetor. Depending on the requirements of each specific application, the carburetor is disassembled by Racing Beat’s carburetor technicians then reworked, retuned, and reconfigured specifically for use with a designated rotary engine application. This process is not a simple “re-jetting” project, but a complex series of steps requiring machining, drilling and reconfiguring of the main and metering bodies, adjustment of the float bowls, and complete replacement of all jets.
SKU: 16630 -
HOLLEY CARBURETOR ONLY, 13B 4-PORT 465CFM RACING BEAT MODIFIED
Racing Beat Modified Holley Carburetor Only, 13B 4-Port 465CFM Stock port Discontinued
Sorry, this item has been discontinued by the Manufacturer
WE offer the extremely popular Racing Beat-modified High Performance Holley carburetor – 465cfm body – for the 1974-75 13B Non-Ported engine application. This carburetor body is the same modified component that is included in our complete 1974-75 13B Non-Ported engine kit. The optional air cleaner assembly and manifold shown are not included, but are available with the complete kit, or as separate items.
Each carburetor is modified by Racing Beat to maximize the performance of a specific engine application. Every carburetor is disassembled, modified and reworked by a Racing Beat carburetor technician. These modifications are the results of countless hours of engine dyno testing and real-world testing. These extensive modifications are undertaken to increase the airflow to meet the demands of the rotary engine.
This carburetor requires the use of a high performance fuel pump delivering 6 psi @ 20 gph, we suggest the use of the Mallory 4070M unit.
SKU: 16633 -
HOLLEY CARBURETOR ONLY, 13B 6 PORT 600CFM RACING BEAT MODIFIED
Racing Beat Modified Holley Carburetor Only, 13B 6 PORT 600CFM 84-92
We offer the extremely popular Racing Beat-modified High Performance Holley carburetor – 600cfm Double Pumper body with mechanical secondaries and manual choke – for the 1986-92 13B 6-Port Non-Ported engine application. This carburetor body is the same modified component that is included in our complete 1986-92 13B 6-Port Non-Ported engine kit. The optional air cleaner assembly and manifold shown are not included, but are available with the complete kit, or as separate items.
Each carburetor is modified by Racing Beat to maximize the performance of a specific engine application. Every carburetor is disassembled, modified and reworked by a Racing Beat carburetor technician. These modifications are the results of countless hours of engine dyno testing and real-world testing. These extensive modifications are undertaken to increase the airflow to meet the demands of the rotary engine. Each finished carburetor is bench checked by chief engineer/engine builder Jim Mederer.
This carburetor requires the use of a high performance fuel pump delivering 6 psi @ 20 gph, we suggest the use of the Mallory 4070M unit.
For optimum performance, combine this Holley carburetor with a matched Racing Beat intake manifold.
SKU: 16637 -
HOLLEY CARBURETOR ONLY, 13B BRIDGE PORT 650 RACING BEAT-MODIFIED
Racing Beat Modified Holley Carburetor Only Bridgeport 13B (uses 650 cfm carb.)
We offer the extremely popular Racing Beat-modified High Performance Holley carburetor for the 1974-85 13B 4-Port Bridge-Ported engine application. This 650 cfm – Double Pumper with mechanical secondaries – carburetor is the same modified component that is included in our complete 1974-85 13B 4-Port Bridge-Port Kit. The optional air cleaner assembly, fuel line, and manifold shown are not included, but are available with the complete kit, or as separate items.
Each carburetor is modified by Racing Beat to maximize the performance of a specific engine application. Every carburetor is disassembled, modified and reworked by a Racing Beat carburetor technician. These modifications are the results of countless hours of engine dyno testing and real-world testing. These extensive modifications are undertaken to increase the airflow to meet the demands of the rotary engine.
This carburetor requires the use of a high performance fuel pump delivering 6 psi @ 20 gph, we suggest the use of the Mallory 4070M unit.
For optimum performance, combine this Holley carburetor with a matched Racing Beat intake manifold and the Holley Float Bowl Fuel Line.
SKU: 16639 -
HOLLEY CARBURETOR ONLY, 13B TURBO 600CFM RACING BEAT MODIFIED
Racing Beat Modified Holley Carburetor Only, All Turbo II 13B Street Port engines 87-92 (uses 600cfm carb.) For normally aspirated use, not designed for use with a turbo charger.
We offer the extremely popular Racing Beat-modified High Performance Holley carburetor for the 1987-91 RX-7 TURBO II 13B rotary engine, configured without a turbocharger, and ported with our streetport intake/exhaust templates. This carburetor body is the same modified component that is included in our complete Racing Beat-modified High Performance Holley Intake System Kit for the 1987-91 RX-7 TURBO II 13B rotary engine. Additionally, this modified carburetor includes a cold start choke feature; a float bowl connection for a mechanical Metering Oil Pump; and great top end power! We recommend the Mallory 4070M internally regulated pump (6 psi) for use with this carburetor, or you may source an equivalent unit locally (the MAZDA OEM fuel injection fuel pump should not be used with this kit). The optional air cleaner assembly and manifold shown are not included, but are available with the complete kit, or as separate items.
The heart of every RX-7 Holley intake kit is a Racing Beat-modified, performance-proven Holley carburetor. We start with brand new Holley carburetor bodies that are disassembled by Racing Beat’s carburetor technicians and extensively modified in-house for use with a designated rotary engine application–stock port, street port, or bridgeport. This process is not a simple “re-jetting” project, but rather a complex series of steps requiring machining, drilling, and reconfiguring of the carburetor body itself as well as the primary and secondary metering bodies, adjustment of the float bowls, and complete replacement and/or re-drilling of all jets. These modifications are the result of countless hours of engine dyno testing and real-world testing.
For optimum performance, combine this Holley carburetor with a matched Racing Beat intake manifold.
SKU: 16629 -
HOLLEY MOP FITTING
Holley MOP Fitting
5/16 24 Thread x 3/16 hose
Goes into float level plug on a Holley.SKU: 91033 -
HOLLEY THROTTLE CABLE BRACKET
Holley, Throttle Cable Bracket
If you have a 6 port, refer to Part Number 18061.SKU: 91100 -
HOLLEY THROTTLE CABLE BRACKET 6-PORT
Holley, Throttle Cable Bracket for 6-Port
If you have a non 6-Port refer to Part Number 91100.SKU: 18061