General Hardware
-
-10 CAP PLASTIC, FITS -10 MALE END
-10 Plastic Cap, Fits -10 Male End
Plastic Cap for male end
These come in very handy when you are removing the engine or cooler, to prevent debris from getting in.
SKU: -10-CAP -
-10 HOSE END 45 DEGREE, TUBE
-10 Hose End 45 Degree, Tube 45 Degree
There are some custom applications where the available oil cooler line sets will just not work, and special length lines need to be assembled. We carry -10 ends in either straight, 45 degree, or 90 degree, as well as -10 hose.SKU: -10-END-45 -
-10 HOSE END 90 DEG, -10 HOSE TO 18MM 90
-10 Hose End, 90 Degree, -10 Hose To 18mm 90 degree
Designed specifically for 86-92 RX-7’s to fit in between the oil cooler and frame rail, where your conventional 90° bend will not. Also works for 93-95 oil filter tower, which is 18mm if you are making lines.SKU: 7736-9010M18A Manufacturer SKU: 7736-9010M18A -
-10 HOSE END 90 DEGREE, TUBE 90 DEGREE
-10 Hose End 90 Degree, Tube 90 Degree
There are some custom applications where the available oil cooler line sets will just not work, and special length lines need to be assembled. We carry -10 ends in either straight, 45 degree, or 90 degree, as well as -10 hose.SKU: -10-END-90 -
-10 HOSE END, STRAIGHT
-10 Hose End, Straight
There are some custom applications where the available oil cooler line sets will just not work, and special length lines need to be assembled. We carry -10 ends in either straight, 45 degree, or 90 degree, as well as -10 hose.SKU: -10-END -
-10 PLUG PLASTIC, FITS -10 FEMALE END
-10 Plastic Plug, Fits -10 Female End
These come in very handy when you are removing the engine or cooler, to prevent debris from getting in, and oil from leaking out.
SKU: -10-PLUG -
10MM CRUSH WASHER 74-11 WATER DRAIN ETC
Water Drain Plug Crush Washer 10mm 74-11
SKU: 41-0000-9956 Manufacturer SKU: 9956-41-000 -
12mm Sealing Washer – Pulsation Damper, Oil Banjo, etc…
12mm Crush Washer seal for many applications
SKU: 13-4830-N236 Manufacturer SKU: N236-13-483 -
14mm Copper Sealing Washer – 93-95 Oil Banjo etc
14mm Crush Washer seal for many applications. These are copper, for aluminum see here
SKU: 21-4000-9956 Manufacturer SKU: 9956-21-400 -
ADAPTER -10 16MM THREAD, -85 COOLER AND -91 FRONT COVER
Adapter, -10, 16mm Thread, Up to 85 Cooler And Up to 91 Front Cover.
SKU: 11901 -
ADAPTER -10 18MM THREAD, 86+ COOLER & ALL REAR HOUSING
Adapter -10, 18mm Thread, 86+ Cooler & All Rear Housing
SKU: 11902 -
ADAPTER OIL COOLER, — NLA —16MM OEM OIL HOSE
Sorry, this item has been discontinued by Mazda.
Adapter Oil Cooler, 16mm, OEM Oil Hose
Fits between front of stock oil cooler hose and oil coolerSKU: 41-200F-9938 Manufacturer SKU: 9938-41-200F -
ADAPTER WATER TEMPERATURE, 3/8 NPT TO MECHANICAL TEMPERATURE GAUGE
Water Temperature, 3/8 NPT To Mechanical Temperature Gauge Adapter
SKU: 2263 -
BATTERY HOLD DOWN, NUT 6MM BIG FLANGE
Battery Hold Down Nut, 6mm Big Flange
SKU: 00-603B-9994 Manufacturer SKU: 9994-00-603B -
BOLT FLEXPLATE RX8, FLEXPLATE TO COUNTERWEIGHT
Flexplate To Counterweight Bolt RX8
SKU: 41-0350-9978 Manufacturer SKU: 9978-41-035 -
BOLT FLEXPLATE, ALL RX7 TO COUNTERWEIGHT
Flexplate To Counterweight Bolt, All RX7
SKU: 41-0160-9978 Manufacturer SKU: 9978-41-016 -
BOLT FRONT PULLEY, 04-11 RENESIS OEM
OEM Front Pulley Bolt, 04-11 Renesis
SKU: 11-4060-N3H1 Manufacturer SKU: N3H1-11-406 -
BOLT FRONT PULLEY, 86-92 OEM
OEM Front Pulley Bolt, 86-92
SKU: 11-420B-N318 Manufacturer SKU: N318-11-420B -
BOLT FRONT PULLEY, 86-92 TITANIUM
Titanium Front Pulley Bolt, 86-92
SKU: 11-420B-N318-TI Manufacturer SKU: N318-11-420B-TI -
BOLT FRONT PULLEY, 93-95 OEM
OEM Front Pulley Bolt, 93-95
SKU: 11-4060-N3C1 Manufacturer SKU: N3C1-11-406 -
BOLT INTAKE MANIFOLD, 86-88 TURBO CENTER LONG
Intake Manifold Bolt, 86-88 Turbo Center Long
SKU: 60-8800-9979 Manufacturer SKU: 9979-60-880 -
BOLT INTAKE MANIFOLD, 89-92 TURBO CENTER LONG
Intake Manifold Bolt, 89-92 Turbo Center
This is the long bolt in the center of the manifold which is hard to find outside of Mazda.
Bolt is 4.5″ LongSKU: 00-8115-9980 Manufacturer SKU: 9980-00-8115 -
BOLT STARTER LOWER, 72-85 COARSE THREAD —NLA—
Lower Starter Bolt, 72-85 Coarse Thread
SKU: 11-0320-9980 Manufacturer SKU: 9980-11-032 -
BOLT STARTER LOWER, 72-92 COARSE THREAD
Lower Starter Bolt, 72-92 Coarse Thread
SKU: 18-4010-N327 Manufacturer SKU: N327-18-401 -
BOLT STARTER LOWER, 93-95 MANUAL TRANSMISSION LOWER
Lower Starter Bolt, 93-95 Manual Transmission
SKU: 61-0300-9979 Manufacturer SKU: 9979-61-030 -
BOLT STARTER UPPER, 86-95
Upper Starter Bolt, 86-95
Note: Which upper starter bolt you use is determined by the starter, not the engine
SKU: 01-0135-9980 Manufacturer SKU: 9980-01-0135 -
BOLT STARTER UPPER, ALL -85
Upper Starter Bolt, All up to 85
Note: which upper starter bolt you use is determined by the starter, not the engine
SKU: 31-0125-9980 Manufacturer SKU: 9980-31-0125 -
BOLT TENSIONER, 86-92 — NLA — 9 INCH
Sorry, this item has been discontinued by Mazda.
SKU: 15-9660-N326 Manufacturer SKU: N326-15-966 -
BOLT TENSIONER, 86-92 3.5 INCH
Tensioner Bolt, 86-92 3.5 Inch
SKU: 50-6900-9979 Manufacturer SKU: 9979-50-690 -
BOLT TENSIONER, 86-92 6 INCH
Sorry, this item has been discontinued by Mazda.
Tensioner Bolt, 86-92 6 InchSKU: 15-9660-N327 Manufacturer SKU: N327-15-966 -
BOTTOM STARTER STUD, 74-92 ALL
Bottom Starter Stud, 74-92 All
Tired of trying to find that ONE COARSE thread bolt for the bottom of the starter?
Replace it with this coarse/fine stud and use the same nut / thread as all the other bellhousing bolts!SKU: STUD10x1.5-1.25 -
-
CENTER HOUSING WATER DRAIN PLUG, LONG 86-92
Water Drain Plug, Center Housing 86-92 Long
SKU: 10-4150-N225 Manufacturer SKU: N225-10-415 -
CLUTCH HARDWARE FOR RACE 7.25″ RALLY TWIN
Race Clutch Hardware for 7.25″ Rally Twin
SKU: 298063RY-HW-725 -
CLUTCH RACE HARDWARE, FOR 5.5″ DOUBLE DISC
Race Clutch Hardware, For 5.5″ Double Disc Race Clutches using our Race Flywheels
SKU: 284063-HW-5.5 -
CLUTCH RACE HARDWARE, FOR 7.25″ TWIN DISC
Race Clutch Hardware, For use with 7.25″ Twin disc Clutches using our Race Flywheels
SKU: 298062-HW-725 -
DOWEL PIN 93-95 AUTO, REAR HOUSING TO STARTER
Rear Housing to Starter Dowel Pin 93-95 Automatic Trans
SKU: 41-2080-9923 Manufacturer SKU: 9923-41-208 -
DOWEL PIN FRONT & REAR STATIONARY GEAR TO HOUSING
Front and Rear Stationary Gear to Housing Dowel Pin
SKU: 10-2030-0839 Manufacturer SKU: 0839-10-203 -
DOWEL PIN SHORT, FRONT COVER & BELLHOUSING
Front Cover and Bellhousing Short Dowel Pin
SKU: 10-3090-1757 Manufacturer SKU: 1757-10-309 -
DRY SUMP ADAPTER #1, ALUMINUM AN -12
Aluminum AN Dry Sump Adapter #1, -12
SKU: 14-R960-ZR03 Manufacturer SKU: ZR03-14-R96 -
DRY SUMP ADAPTER #2, ALUMINUM AN -16
Aluminum Dry Sump Adapter #2, AN -16
SKU: 14-R980-ZR03 Manufacturer SKU: ZR03-14-R98 -
EGR EXPANSION PLUG, 86-88
OEM freeze plug for 86-88 Non Turbo center housing – goes below intake ports.
SKU: 52-8000-9930 Manufacturer SKU: 9930-52-800 -
EXHAUST SLEEVE, TITANIUM 13B
Works great to replace non-turbo 13B sleeves and 20B sleeves.
Browse our 3 Rotor Engine Parts Catagory.
SKU: EXH-SLEEVE-TI -
EXHAUST STUD 89-92, TURBO TO DOWNPIPE
Exhaust Stud 89-92, Turbo To Downpipe
This item has been discontinued by Mazda
SKU: 13-7080-N370 Manufacturer SKU: N370-13-708 -
FLYWHEEL HARDWARE, STEEL 74-92,TURBO, RACE
Steel Flywheel Hardware Kit, 74-92, Turbo, Race
Flywheel to Counterweight Bolt SetSKU: 95179 -
FREEZE PLUG LARGE, ALL FRONT & REAR HOUSING
1 3/16″ diameter Mazda OEM freeze plug for the larger holes front and rear side housings.
( uses 6-7 depending on year)
SKU: 63-0000-9930 Manufacturer SKU: 9930-63-000 -
FREEZE PLUG SMALL, FRONT HOUSING
Freeze Plug Small (3/4″ Diameter), Front Housing
(for front side housing, uses 1)SKU: 62-0000-9930 Manufacturer SKU: 9930-62-000 -
FREEZE PLUG, ROTOR HOUSING @ INTAKE MANIFOLD
Freeze Plug, Rotor Housing @ Intake Manifold
SKU: 555-101 -
FRONT ENGINE MOUNT BOLT, PLATE TO FRONT COVER 72-85 (ea)
Front Engine Mount Bolt. Plate to Front Cover. 72-85 RX7 (ea)
SKU: 10-1015-0250 Manufacturer SKU: 0250-10-1015 -
FUEL DOOR BUMP STOP, 81-85 RX7, 93-95 RX7, & 04-11 RX8
Fuel Door Bump Stop (Two per Vehicle)
Fits 81-85 RX7
93-95 RX7
04-11 RX8SKU: 70-4910-0187 Manufacturer SKU: 0187-70-491 -
FUEL FILTER MOUNT, 86-92 (EACH)
Fuel Filter Mount, 86-92 (Each)
2 RequiredSKU: 13-3630-N236 Manufacturer SKU: N236-13-363 -
HYLOMAR TUBE, 1.5 OZ
Best chemical we have found for water seal O-rings. Brush it on with a trimmed down “acid” brush – in the water seal grooves and then on the seals after you have placed them into the grooves. Stays tacky for a LONG time.
One tube will do one engine easily.
SKU: HYLOMAR -
OIL HOSE FITTING, 93-95 & 04-11, END WITH CLIP
Oil Hose Fitting, 93-95 & 04-11, End With Clip
SKU: 14-850A-N3G1 Manufacturer SKU: N3G1-14-850A -
OIL HOSE RETAINING CLIP, SUPERSEDED USE N3G1-14-850A
This item has been superseded. Now use N3G1-14-850A
SKU: 14-6220-N3A1 Manufacturer SKU: N3A1-14-622 -
OIL PAN BOLT SET —NLA — (FOR ALL 2-ROTOR ENGINES) 22 – BOLTS
Sorry, no longer available.
Oil Pan Bolt Set (For All 2-Rotor Engines) 22 – BoltsSKU: OIL-PAN-BOLT-SET -
OIL PRESSURE SENDING UNIT PLUG, 1/8 BSP
Oil Pressure Plug, 1/8 BSP, Plug
SKU: 31-000J-9950 Manufacturer SKU: 9950-31-000J -
Plug Oil Injector Hole (rotor housings + intake manifold)
Plug for plugging oil injector holes (rotor housings + intake manifold) when they are not being used. Sold EACH, you typically need 2 or 4 depending what you are doing. Fits all oil injector holes from 84-11. Supplied with sealing washer. Uses 3/16 allen wrench.
SKU: 19-064A-FT01-RT Manufacturer SKU: FT01-19-064A-RT -
POWERPLANT FRAME TAPER BOLT 93-11
Powerplant Frame Taper Bolt 93-11
SKU: 39-0660-FD01 Manufacturer SKU: FD01-39-066 -
RIVET PLASTIC 86-ON, PUSH BUTTON TYPE -NLA-
This item has been discontinued by Mazda
Plastic Push Button Type Rivet, 86-On
SKU: 56-81X0-FB01 Manufacturer SKU: FB01-56-81X -
RIVET PLASTIC, FAN SHROUD LOWER
Plastic Rivet, Fan Shroud, Lower
SKU: 40-6580-9926 Manufacturer SKU: 9926-40-658 -
-
SCREW BRAKE ROTOR, ALL YEARS (EACH)
Brake Rotor Screw, All Years, Phillips Flat Head, Counter Sunk
Sold individuallySKU: 10-8200-9983 Manufacturer SKU: 9983-10-820 -
TURBO OIL FEED BANJO BOLT 12MM 86-92
Turbo Oil Feed Banjo Bolt 12mm 86-92
Banjo bolt for top left front of front side housing for the oil feed to the turbo.SKU: 91-2000-9936 Manufacturer SKU: 9936-91-200 -
TURBO OIL FEED BANJO BOLT 14MM 93-99
Turbo Oil Feed Banjo Bolt 14mm 93-99
Banjo bolt at top left of front side housing for the oil feed to the turbo, 14mm for 93-99’s.SKU: 91-4000-9936 Manufacturer SKU: 9936-91-400 -
WEBER IDLE SPEED SCREW
Weber Idle Speed Screw
Spring is not included. It is 47600.007Browse our Weber Carbs, Manifolds and Parts section
SKU: 64625.012 -
WEBER INLET FITTING for 8mm (5/16″) push on hose
Weber 12mm Inlet Fitting for a regular 5/16″ rubber hose.
All Weber IDA carbs come with a useless banjo fitting we have never figured out how to use (unless you tap it 1/8-pipe and use a “barb” fitting). This will replace the stock inlet fitting with a hose nipple that you can push on and clamp regular fuel hose to. This is the stock fuel hose size for all Mazda RX cars.
Click Here for a Weber 48IDA Suggested Parts List
Browse our Weber Carbs, Manifolds and Parts section
SKU: 99301.380 Manufacturer SKU: 99301.380 -
WEBER INLET FITTING, AN -6 TO WEBER 12MM
-6 To Weber 12mm Inlet Fitting
All Weber IDA carbs come with a useless banjo fitting we have never figured out how to use (unless you tap it 1/8-pipe and use a “barb” fitting). This will replace the stock inlet fitting with -6AN so you can use braided hose.
The 12mm Stat-O-Seal is strongly recommended for this fitting — it is at: WEBER INLET SEAL, STAT-O-SEAL FOR 12MM
We also have a 90° fitting for 8mm / 5/16″ push on hose at: WEBER INLET FITTING for 8mm (5/16″) push on hoseClick Here for a Weber 48IDA Suggested Parts List
Browse our Weber Carbs, Manifolds and Parts section
SKU: 30606-M12D -
WEBER INLET SEAL, STAT-O-SEAL FOR 12MM
Weber Inlet Seal, Stat-O-Seal FOR 12mm
This is the seal needed for the -6AN fuel inlet fitting for Weber carbs.Click Here for a Weber 48IDA Suggested Parts List
Browse our Weber Carbs, Manifolds and Parts section
SKU: 357-12MM-STAT -
WEBER NUT 8X1.25 WITH 10MM HEX
Weber Nut 8X1.25 With 10mm Hex
These are needed for the larger bore carbs as there is not enough room to get a 12mm wrench correctly on the base nuts.
These use a 10mm wrench which gives you room to tighten the nut.
Hard to find in “not jet nut” style and in steel. They can come in handy in many other places also.Click Here for a Weber 48IDA Suggested Parts List
Browse our Weber Carbs, Manifolds and Parts section
SKU: 967-NUT -
WEBER SHAFT LEVER, 48+51IDA MAZDA CABLE
Weber Shaft Lever, 48+51 IDA Mazda Cable
For “U.S. Style” manifolds – where the cable pulls from BELOW shaft.Click Here for a Weber 48IDA Suggested Parts List
Browse our Weber Carbs, Manifolds and Parts section
SKU: 444614.04 -
WEBER SHAFT LEVER, WITH STOP PIN LEFT
Weber Shaft Lever, With Stop Pin Left. 14ga steel
We have these “stops” made for us so the throttle STOP is on the same side of the carb as the throttle PULL. Adjusted correctly this prevents the throttle shaft from being bent when full throttle is applied.Click Here for a Weber 48IDA Suggested Parts List
Browse our Weber Carbs, Manifolds and Parts section
SKU: MAT460-L -
WEBER SHAFT LEVER, WITH STOP PIN RIGHT
Weber Shaft Lever, With Stop Pin Right
This STOP is for when the carb fuel inlet is on the Engine side, cable pulling from ABOVE the shaft.
These are for what we call “Australian Style” manifolds.Browse our Weber Carbs, Manifolds and Parts section
SKU: MAT460-R -
WEBER SHAFT LOCK TAB
Weber Shaft Lock Tab Washer Fits IDA or DCOE Sold Each
Part can be referenced at #26
Browse our Weber Carbs, Manifolds and Parts section
SKU: 55520.004 Manufacturer SKU: 55520.004 -
WEBER SHAFT NUT
Weber Shaft Nut Fits IDA or DCOE Sold Each
Part can be referenced at #25
Browse our Weber Carbs, Manifolds and Parts section
SKU: 34710.003 -
WEBER SHAFT WASHER
Weber Shaft Washer Fits IDA or DCOE Sold Each
Reference part at #27
Browse our Weber Carbs, Manifolds and Parts section
SKU: 99024.258 -
WEBER SPRING for EITHER IDLE SPEED OR MIXTURE SCREW
Weber Spring for Either Idle Speed or Mixture Screw
Browse our Weber Carbs, Manifolds and Parts section
SKU: 47600.007 -
WEBER STUD, 8X1.25 35MM
Weber Stud, 8X1.25 35mm
Click Here for a Weber 48IDA Suggested Parts List
Browse our Weber Carbs, Manifolds and Parts section
SKU: AV11981 -
WEBER STUD, 8X1.25 45MM
Weber Stud, 8X1.25 45mm
Most of the Weber Manifolds do not include studs to hold the carb to the manifold. These 45mm ones work great when you are using spacers — measure to be sure these are what you need – depends on the spacer thickness.Browse our Weber Carbs, Manifolds and Parts section
SKU: AV11983