OIL COOLER, 04-08 RX8 LEFT
Oil Cooler, 04-08, RX8, Left (Manual+Auto)
SKU: | 14-700D-N3H1 |
Manufacturer SKU: | N3H1-14-700D |
OIL COOLER, 04-08 RX8 LEFT
$723.43
Related Products:
-
OIL COOLER, 04-08 RX8 RIGHT
Oil Cooler, 04-08, RX8 Right (6-Speed only)
SKU: 14-700D-N3H6 Manufacturer SKU: N3H6-14-700D -
OIL COOLER BYPASS THERMOSTAT, -10 AN MALE 180 DEGREE
Oil Cooler Bypass Thermostat, -10 AN Male, 180 Degree
Use when building an oil cooing system with aftermarket cooler(s).
SKU: A0T2-3 -
OIL COOLER HOSE SET, 04-08, RX8 AUTOMATIC OEM AT LEFT COOLER
Oil Cooler Hose Set, 04-08, RX8, Automatic, OEM, At Left Cooler
SKU: 14-830H-N3H1 Manufacturer SKU: N3H1-14-830H -
OIL HOSE FITTING, 93-95 & 04-11, END WITH CLIP
Oil Hose Fitting, 93-95 & 04-11, End With Clip
SKU: 14-850A-N3G1 Manufacturer SKU: N3G1-14-850A -
OIL COOLER HOSE SET, 04-08 RX8 STAINLESS
OIL COOLER HOSE SET, 04-08 RX8 STAINLESS
This set of fully assembled Stainless Steel Braided Hoses replaces the original factory oil cooler hoses on the 2004-2008 RX-8 Manual Transmission models (equipped with dual oil coolers). Costing much less than Mazda replacement units (over $1100 for the complete Mazda set!).
11911 Oil Hose Set-Installation Instructions
Racing Beat’s fully assembled Stainless Steel Braided Hose Set replaces the original factory oil cooler hoses on the 2004-2008 RX-8 Manual Transmission models (equipped with dual oil coolers). Costing much less than Mazda replacement units (over $1100 for the complete Mazda set!), the Racing Beat Oil Hose sets will meet the demands of both street and race.
Simplify your oil line system by replacing the original EIGHT (8) factory lines with the streamlined Racing Beat kit, which contains only the three (3) most critical lines – 1) engine out-to-cooler, 2) cooler-to-cooler, and 3) cooler-to-engine in.
The Mazda factory lines combine both rigid and flexible tubing, and include ten (10) mid-hose connector fittings. Replacing this complex combination of hosing and connectors with a simplified performance-based set eliminates possible areas of leakage during racing and high output applications. As the old saying goes, “Simple is better!” Produced in-house at Racing Beat using Earl’s Auto-Flex stainless steel braid-protected synthetic rubber hose and featuring an inner liner of synthetic rubber, including partial cover of stainless steel braid embedded into the liner during manufacturing. The hose liner is then bonded to a outer protective sheath of stainless steel wire braid. Precision-machined aluminum Earl’s Auto-Seal and Swivel-Seal hose ends ensure a secure and superior seal. Each line is pressure tested by Racing Beat at the end of the assembly process. Unlike earlier rotary applications, replacement of the oil lines on the RX-8 application requires substantial labor effort and is best undertaken when the engine has been removed from the vehicle. Although more challenging due to limited access, this project can be undertaken with engine in the vehicle, just allow adequate time to complete the process. With the engine in the vehicle this is an involved project that can’t be rushed!
Shipped complete with all required oil lines, oil cooler adaptors, engine adaptors, bracket hardware, protective end caps, and fully detailed installation instructions.
SKU: 11911 -
GRILLE SCREEN OIL, 04-08 OIL COOLER -EACH
Oil Cooler Screen, 04-08 (Each)
These screens are sold as individual units. Review the following ordering information:
A. Manual transmission RX-8 requires two (2) screens.
B. Automatic transmission equipped RX-8 is equipped with only one (1) oil cooler and requires only one (1) screen.SKU: 11807